Generac Power Systems 7 kW PowerPact Owner'S Manual Download Page 11

 Automatic Standby Generator Owner’s Manual

7

2.4 — Specifications

2.4.1 — Generator

2.4.2 — Engine

The specification sheet for your generator was included in the documentation provided with the unit at the time of purchase. For additional 
copies, consult your local Authorized Service Dealer for your specific generator model.

2.4.3 — Fuel Requirements

The engine has been fitted with a dual fuel carburetion system. The unit will run on natural gas or LP gas (vapor), but it has been factory set to 
run on natural gas. The fuel system will be configured for the available fuel source during installation. 
Recommended fuels should have a btu content of at least 1,000 Btus per cubic foot (37.26 megajoules per cubic meter) for natural gas, or at 
least 2,500 Btus per cubic foot (93.15 megajoules per cubic meter)

 

for LP gas (vapor).

NOTE: If converting to LP gas from natural gas, a minimum LP tank size of 250 gallons (946 liters) is recommended. See the Installation 
Manual for complete procedures and details.

Output

7 kW

Rated Voltage

240

Rated Maximum Load 
Current (Amps) at 240 
Volts (LP)*

29.2

Main Circuit Breaker

30 Amp

Phase

1

Rated AC Frequency

60 Hz

Battery Requirement

Group U1, 12 Volts and 300 CCA Minimum (Generac Part No. OD4575)

Weight (unit only in lbs./
kg)

280/127.3

Enclosure

Galvanneal Steel

Normal Operating 
Range

This unit is tested in accordance to UL 2200 standards with an operating temperature of -20 ºF (-29 ºC) to 122 ºF (50 ºC). For areas 

where temperatures fall below 32 ºF (0 ºC) a cold weather kit is required. When operated above 77 ºF (25 ºC) there may be a decrease 

in engine power. Please reference the engine specifications section.

These generators are rated in accordance with UL 2200, Safety Standard for Stationary Engine Generator Assemblies, and CSA-C22.2 No. 100-04 
Standard for Motors and Generators.
* Natural Gas ratings will depend on specific fuel Btu/joules content. Typical derates are between 10-20% off the LP gas rating.
** Circuits to be moved must be protected by same size breaker. For example, a 15 Amp circuit in the main panel must be a 15 Amp circuit in the transfer switch.

Type of Engine

GA-420

Number of Cylinders

1

Displacement

420 cc

Cylinder Block

Aluminum w/Cast Iron Sleeve

Recommended Spark Plug

F7TC/ Champion N9YC

Spark Plug Gap

0.76 mm (0.030 in)

Starter

12 VDC

Oil Capacity Including Filter

Approx. 1.2 Qt/1.1 L

Recommended Air Filter

 Generac Part No. 0E9371A

Engine power is subject to and limited by such factors as fuel Btu/joules content, ambient temperature and altitude. Engine power decreases about 
3.5 percent for each 1,000 feet (304.8 meters) above sea level, and also will decrease about 1 percent for each 10 ºF (6 ºC) above 60 ºF (15 ºC) 
ambient temperature. 

Summary of Contents for 7 kW PowerPact





































Reviews: