Generac Portable Products 1450-0 Owner'S Manual Download Page 6

Generac Portable Products 2,400 PSI High Pressure Washer

6

Attach Spring Clips to Handle

• Attach spring clips to the left side (viewing from the

rear of the unit) of the handle with the self tapping

screws in the holes provided.

• Place the extension with turbo nozzle in the spring

clips, as shown in Figure 2.

Add Engine Oil

IMPORTANT:

Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine failure.
• Place pressure washer on a level surface.
• Refer to the engine owners manual to add

recommended oil to engine.

NOTE: Check oil often during engine break–in.

Refer to engine owner’s manual.
NOTE

: The pump is pre-lubricated and sealed,

requiring no additional lubrication for the life of the

pump.

Add Gasoline

DANGER!

Never

fill fuel tank indoors. Never fill

fuel tank when engine is running or hot. 

Do Not

smoke when filling fuel tank.

WARNING!

Never

fill fuel tank completely full.

Provide space for fuel expansion. Wipe away

any fuel spillage from engine and equipment

before starting.

• Use clean, fresh, unleaded fuel and store in

approved, clean, covered containers. Use clean fill

funnels. 

Never

use “stale” gasoline left over from

last season or gasoline stored for long periods.

• Clean area around fuel fill cap, remove cap.
• Slowly add gasoline to fuel tank. Use a funnel to

prevent spillage. Fill tank to “Fuel Level Mark”, as

shown in Figure 3.

• Install fuel cap and wipe up any spilled gasoline.

Connect Hose and Water Supply to

Pump

IMPORTANT:

You must attach all hoses before you

start the engine. Starting engine without all hoses

connected and water supplied will damage the pump.
• Uncoil the high pressure hose and attach one end of

the hose to the base of the spray gun. (Figure 4).

Tighten by hand.

• Attach the other end of the high pressure hose to

the high pressure outlet on the pump (Figure 5).

Tighten by hand.

Figure 2 — Place Extension with Turbo Nozzle in Spring

Clips

Figure 3 — Add Gasoline to Fuel Tank.

Figure 4 — Connect High Pressure Hose to Spray Gun

Spring Clips

Summary of Contents for 1450-0





















Reviews: