Gemini GEM-RP1CAe2 Operating Manual Download

Page: 34 / 40

S Y S T E M T R O U B L E E R R O R C O D E S

Trouble

Indication

System Trouble

Condition

Action

E10-NN

Keypad Response

Call installing company for service.

E11-NN

Keypad Tamper

A keypad has been removed from the wall. Call installing company for service if problem

E12-NN

Expansion Zone
Module Response

Call installing company for service.

E13-NN

Expansion Module

The cover has been removed from a zone expansion module. A problem has been detected

E16-NN

Wireless Receiver

A problem has been detected with the wireless receiver. Call installing company for service.

E17-NN

Receiver Tamper
Condition

Call installing company for service.

E18-NN

KeyFob Transmitter
Low Battery

The batteries in the wireless KeyFob transmitter indicated are low and should be replaced.
The replacement battery is the Duracell 386 Lithium battery.

Warning: Replace batteries only with the same type as specified above. Use of another

battery may present a risk of fire or explosion. Do not recharge or disassemble battery, or

dispose of in fire.

Summary of Contents for GEM-RP1CAe2









































Search results

Summary of Contents for GEM-RP1CAe2

Reviews:

Related manuals for GEM-RP1CAe2

Brands by name

Popular brands

Gemini GEM-RP1CAe2, Operating Manual

Search results

Summary of Contents for GEM-RP1CAe2

Reviews:

Related manuals for GEM-RP1CAe2

Brands by name

Popular brands