manualshive.com logo in svg

Gemini GEM-RP1CAe2, Operating Manual

Share
Download
Gemini GEM-RP1CAe2 Operating Manual Download Page 33

33 

S Y S T E M   T R O U B L E   E R R O R   C O D E S  

Trouble  

Indication 

System Trouble 

Condition 

Action 

 

E04-NN 

Wireless Transmitter  
Supervisory Failure 

A problem has been detected with a wireless transmitter. Call installing company for service 

E05-NN 

Wireless  Transmitter 
Low Battery 

The battery in a wireless transmitter is low and should be replaced. This transmitter  is on the 
zone corresponding to the number NN. The replacement battery for the GEM-TRANS2 door/
window transmitter, GEM-PIR motion detector and GEM-GB glass break detector is the 
Duracell DL123A 3 volt lithium.  (2 required for the GEM-PIR and GEM-GB.) The 
replacement battery for the GEM-SMK is the Duracell MN1604 9 Volt Alkaline (2 required). 
The GEM-DT Dual Technology Sensor requires 4 C cell alkaline batteries.       
 

Warning: Replace batteries only with the same type as specified above. Use of another 

battery may present a risk of fire or explosion. Do not recharge or disassemble battery, or 

dispose of in fire. 

E06-NN 

Receiver Response 
Failure 

Call installing company for service.

 

E07-00 

Download Failure 

Call installing company for service.

 

E08-00 

Telephone Line Cut 

The telephone line has failed. If telephone service has been temporarily interrupted, the 
trouble will clear automatically when it is restored. Otherwise, call installing company for 

E09-00 

System Cold Start 

 

Summary of Contents for GEM-RP1CAe2









































Reviews:

No comments

Brands by name

Popular brands

Load more brands