(7)
3. To
EDIT
a
LOOP
,
press
B-EDIT (21)
and use the
JOG WHEEL (24)
to
adjust the length of the
LOOP
. Press
B-EDIT (21)
again to select a new
EXIT POINT
. The
LOOP
will stay in memory until a new
FLY CUE
POINT
is set or the CD is ejected.
MEMO CUE:
1. Another easy way to set
CUE POINTS
is the
MEMO (CUE-1-5) (23)
.
You can store up to
5 CUE POINTS
in memory from any track within a
CD. Just press
MEMO (23)
then select any
1
of the
5 CUE POINTS
(CUE 1-5)
to set a
CUE POINT
. Once you set a
MEMO CUE POINT
you
can return to that
CUE
by pressing it again. If the CD is
PLAYING
it will
play from the
CUE POINT
and if the CD is
PAUSED
the
CUE POINT
will
be
PAUSED
as well.
MEMO POINTS
are locked in memory until that CD
is ejected from the CD player.
NOTE: THE MEMO CUES CAN ALSO BE SET IN PAUSE MODE USING THE JOG WHEEL FOR
PRECISE CUE POINTS.
PLAY CUE:
1. To memorize the spot at which you want play to start, select the proper
track, and then push the
PLAY/PAUSE (12)
button so the unit goes
into the
PLAY
mode (
PLAY/PAUSE (12)
LED
will glow green). Listen to
the CD and when the CD gets to the approximate spot, push
PLAY/
PAUSE (12)
so the unit goes into
PAUSE
mode (
PLAY/PAUSE (12)
LED
will blink green). Move the
JOG WHEEL (24)
to the precise spot you
want play to begin and push the
PLAY/PAUSE
(12)
button to memorize
the
CUE POINT
. Press the
CUE
BUTTON
(13)
to return to the memorized
CUE POINT
. Push the
PLAY/PAUSE BUTTON
(12)
, and the unit will
instantly play from the spot selected.
2. To fine tune a
CUE POINT
, pause play at the memorized
CUE POINT
(the
CUE/PREVIEW
(13) LED
will glow and the
PLAY/PAUSE (12)
LED
will blink), then use the
JOG WHEEL (24)
to scan frame by frame (1/75th
of a second) to where you want play to begin (the
CUE LED
will blink
while you scan). Press
PLAY/PAUSE (12)
to save the new cue point.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND
THE BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS THE PLAY/PAUSE
(12) TO SAVE THE CUE POINT.
ROBO START INSTRUCTIONS:
IN SINGLE-AUTO CUE MODE:
Use
ROBO START (36)
in
SINGLE-AUTO CUE MODE
to alternate play
between the
CFX-50
two CD players (one track from one side,
then one from the other). In
SINGLE-AUTO CUE MODE
play starts
immediately with no blank or “dead” space.
ROBO START
causes one
side of the CD player to play when the other side is paused.
1. Engage
SINGLE-AUTO CUE MODE
with the
SINGLE
(17)
button.
2. Press the
ROBO START (36)
button to activate
ROBO START
. Play will
alternate between the two CD players. At the end of a track, the playing
side pauses and the other CD deck plays a track. At the end of this
track, the playing side pauses and the first CD deck resumes play.
IN CONTINUOUS MODE OR DURING NORMAL PLAY:
If you use
ROBO START
without
SINGLE-AUTO CUE MODE
(in
CONTINUOUS MODE
or during normal play), play will not alternate
automatically. Pressing pause on the playing side will cause the other
side to play.
1. During normal play, set a
CUE POINT
on the other side of the CD player.
2. Press the
ROBO START (36)
button to activate
ROBO START
(the
button will blink).
3. Press
PLAY/PAUSE
BUTTON
(12)
on the playing side to begin play from
the cue point on the other side.
NOTE: PAUSING THE PLAYING SIDE IN THE MIDDLE OF A TRACK WILL CAUSE THE OTHER
SIDE TO PLAY. WHEN THAT TRACK ENDS, PLAY WILL BEGIN FROM THE MIDDLE OF THE
TRACK WHERE PLAY WAS PAUSED.
PGM:
PROGRAM:
First choose either
DISC 1
or
2
,
and press
STOP (8)
to reset any
previous program on the side that is chosen.
Then press either
A
or
B
(37)
to choose
DISC 1
or
2
. Next press
PGM (37)
for
PROGRAM
mode, (the
PGM LED
will start flashing green). Select the
TRACK
NUMBER
with the
NUMBER PAD
and
SET (37)
afterwards to select a
track for that slot. Continue to press
PGM (37)
and select tracks, until
filled with the total number of tracks. Then press
PLAY/PAUSE (12)
to
start the program (the
PGM LED
will be solid green). To exit the
PROGRAM
press the
STOP (8)
button. The
SINGLE (17) AUTO CUE
mode that is being used, such as
CONTINUOUS
or
SINGLE
modes will
affect the way the tracks play,
ROBO START
will not be affected by
PROGRAMING
.
DIRECT SELECT:
To
DIRECTLY SELECT
a
TRACK
,
just press the
TRACK NUMBER
then
SET (37)
followed by
PLAY/PAUSE (12)
to
PLAY
the last selection.
TROUBLESHOOTING:
•
If the disk will not play,
check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
•
If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
•
If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Type..........................Dual Mechanism Compact Disc Player w/wired remote
Disc Type........................................Standard Compact discs (12 cm & 8 cm)
Time Display..........................Track Elapsed, Track Remain, or Total Remain
Variable Pitch.....± 4%, ± 12%, ± 24%, & ±100% Slider with Resume Switch
Pitch Bend...........................................................................± 20% Maximum
Instant Start..................................................................Within 0.015 seconds
Track Selection........................................................................1 to 99 Tracks
Installation.............................................19" Rack Mountable Player Unit, 3 U
19" Rack Mountable Control Unit, 2 U
AUDIO SECTION:
Quantization...........................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate............................................................................8 Times
Sampling Frequency.........................................................................44.1 kHz
Frequency Response............................................................20 Hz to 20 kHz
Digital Output......................................................................................IEC958
Total Harmonic Distortion....................................................Less Than 0.05%
Signal to Noise Ratio...........................................................................104 dB
Dynamic Range....................................................................................98 dB
Channel Separation..................................................................90 dB (1 kHz)
Output Level.........................................................................1.9 Volts R.M.S.
Power Supply.............................................................AC 120/230V, 60/50 Hz
Dimensions:
Remote Control:.......................W 19” x H 5.1” x D 3” (482 x 131 x 76mm)
Main Unit:...............................W 19” x H 3.5” x D 10” (482 x 88 x 254mm)
Weight:
Remote Control:....................................................................4 lbs (1.8 kg)
Main Unit:.........................................................................10.2 lbs (4.6 kg)
ACCESSORIES:
Operating Instructions..................................................................................1
Warranty Card..............................................................................................1
Power Cord..................................................................................................1
Remote Control Cables:...............................................................................2
Stereo RCA Line Cables..............................................................................2
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
IN THE USA: IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT, PLEASE CALL 1 (732) 738-9003 FOR
GEMINI CUSTOMER SERVICE.
DO NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER.