background image

Intelligent Document Reader AT10Ki User Guide

 

Installing the Reader (Legacy USB)

 

Page 23 of 41 

4. 

Verify that the yellow LEDs are in landing lights sequence and the Reader State in the lower left is 

“Enabled”.  

The reader is ready to accept documents. 

5. 

Select

 the test card (DS-00031 or DS-00034) supplied with the reader. 

 

 

 

6. 

Place the test card face down on the document window, aligned with the left guide, with the test 

card instructions facing up. 

7. 

Push 

the

 card to the back of the document window until it stops.  

Note: 

Do not move the document during the scanning process. 

8. 

Observe

 the lights during the scanning procedure. 

 

The yellow LEDS change from landing lights sequence to progress bar sequence while the 
reader scans and processes the data. Ensure that the document is held still whilst reading. 

 

The OK light (green tick) turns on, indicating a successful read. 

 

The yellow LEDs return to landing lights sequence, indicating that the reader is ready to 
scan another document. 

The data from the test card is sent to the host computer and the results displayed on the PC screen. 
If the test is successful, a screen similar to the following screen is displayed. 

 

 

Summary of Contents for AT10Ki










































Reviews: