gefran Vedo EL35CT Installation And Operation Manual Download Page 9 | Manualshive

Page: 9 / 22

background image

9

80951C_MHW_GF_VEDO EL35CT-EL57CT_03-2010_ENG

To maintain IP65 protection level during panel installation, pay attention to the following points:

•

make the edges of the hole for the panel perfectly smooth and flat

•

tighten each fastening screw

The terminals also have an O-Ring inserted at the rear of the display frames.

Cleaning the device

Clean the device only with a soft cloth and non-abrasive neutral soap. Do not use solvents.

Fig. 7 - O-Ring on GF_VEDO EL57CT terminals

«
...
7
8
9
10
11
...
»

Summary of Contents for Vedo EL35CT























Reviews:

No comments

Related manuals for Vedo EL35CT

Brand: JASSWAY Pages: 11

POS MobilePro III

Brand: Vectron Pages: 112

DS-K1T8003 Series

Brand: HIKVISION Pages: 2

ADAM-3600-A1FN0AE

Brand: Advantech Pages: 60

Brand: DSPPA Pages: 22

Brand: RusGuard Pages: 20

Brand: Ingenico Pages: 2

Brand: Vectron Pages: 83

Brand: Infoton Pages: 34

Brand: Hobex Pages: 32

Brand: red lion Pages: 8

Brand: NetPay Pages: 20

Brand: Anviz Pages: 8

Brand: ELTEX Pages: 80

Brand: PAX Pages: 6

Brand: detekt Pages: 25

Brand: M-system Pages: 183

Brand: Hafele Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands