background image

5

85198A_Manual of Electrical Installation for Pressure Probes KH-SIL2-Mobyle-series_07-2019_ENG

4. Technical specifications

Output signal

VOLTAGE

RATIOMETRIC

CURRENT

Accuracy at room temperature (1)

< ± 0.5% FS

Pressure ranges (2)

From 4 bar to 1000 bar (See table)

Overvoltage

32 Vdc max

Overpressure (without degrading performance)

See table

Pressure containment (burst test) 

See table

Pressure Media

Fluids compatible with Stainless Steel AISI 430F and 17-4 PH 

Housing 

Stainless Steel AISI 304  

Power supply 

 15...30Vdc

5V ±0.25 V

10...30Vdc

  Dielectric strenght

250 Vdc

Zero output signal

0.1V; 0.2V; 0.5V; 1V (*)

0.5 V

4 mA

Full scale output signal 5V; 10V; 10.1V; 10.5V (*)

4.5 V

20 mA

Allowed load

≥ 5KΩ

see load diagram

Long  term  stability    

< 0.2% FSO/per year 

Operating temperature range (process)

-40...+125°C (-40...+257°F)

Operating temperature range (ambient) 

-40...+105°C (-40...+221°F)

Compensated temperature range

-20...+85°C (-4...+185°F)

Storage temperature range

-40...+125°C (-40...+257°F)

Temperature effects over compensated range (zero)

± 0.01% FS/°C typ (± 0.02% FS/°C max.)

Temperature effects over compensated range (span)

± 0.01% FS/°C typ (± 0.02% FS/°C max.)

Response time (10...90%FSO)

< 1 msec.

Warm-up time (3)

< 30 sec.

Mounting position effects

Negligible

Humidity

Fino a 100%RH non-condensing

Weight

80-120 gr. nominal

Mechanical shock

100g/11msec according to IEC 60068-2-27

Vibrations

20g max at 10...2000 Hz according to IEC 60068-2-6

Ingress protection

IP65/IP67

Output short circuit and reverse polarity protection

YES

CE Conformity

According to EC Directive 2004/108/CE

Electromagnetic compatibility-Emission

EN61326-1/EN61326-2-3

Lifetime

10 years

(*) Other voltage values of Zero and Full Scale available on request.

FS = Full scale

1 Incl. Non-Linearity, Hysteresis, Repeatability, Zero-offset and Span-offset (acc. to IEC 61298-2)

2 The operating pressure range is intended from 0.5% to 100% FS

3 Time within which the rated performance is achieved

RANGE 

(Bar)

4

6

10

16

20

25

40

60

100

160

200

250

400

600

1000

Overpressure 

(Bar)

8

12

20

32

40

50

80

120

200

320

400

500

800

1200 1200

Burst pressure

(Bar)

16

24

40

64

80

100

160

240

400

640

800

1000 1500 1500 1500

Summary of Contents for KH-SIL2 Series









Reviews: