gefran KFM LD Instruction Manual Download Page 20 | Manualshive

Page: 20 / 40

background image

2.9.16. Error diagnosis and display options

The KFM LD door drive has an event stack that stores errors and warnings in non-volatile form, for example,

overtemperature of the heat sinks, etc. The error stack can only be read out with one of the service programs.

2.9.17. Signal and fault display by means of light emitting diodes

One possibility for error diagnosis during commissioning is provided by the display of the 4 LEDs on the control

device. Details on the function and meaning can be found in Chap. 5.5 on page 33.
Also see about this the Chap. 4.3 on page 25.

20

KFM LD • Instruction manual

«
...
18
19
20
21
22
...
»

Summary of Contents for KFM LD









































Reviews:

No comments

Related manuals for KFM LD

Brand: ABB Pages: 16

Brand: ABB Pages: 4

Brand: ABB Pages: 52

Brand: Sprint Electric Pages: 8

Brand: D+H Pages: 20

Brand: Danfoss Pages: 2

Brand: D+H Pages: 8

Brand: KEB Pages: 300

Brand: Iomega Pages: 17

Allen-Bradley PowerFlex 753

Brand: Rockwell Automation Pages: 20

PowerFlex 755TM

Brand: Rockwell Automation Pages: 120

Brand: Master Finish Pages: 2

Brand: KEBCO Pages: 24

Brand: Texas Instruments Pages: 22

Brand: OE Max Controls Pages: 58

Brand: ABB Pages: 24

Brand: Magnetek Pages: 122

VLT PTC Thermistor Card MCB 112

Brand: Danfoss Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands