Gefen ToolBox GTB-HD4K2K-642-BLK User Manual Download Page 118

Page: 118 / 122

page | 108

Upgrading using the USB port

Download the firmware update from the Support section of the Gefen Web site.

Power-ON the 6x2 Matrix for HDMI 4K x 2K.

Connect a USB cable between the computer and the 6x2 Matrix for HDMI 4K x 2K.

It is unnecessary to disconnect any audio / video cables from the 6x2 Matrix for HDMI

4K x 2K

during the update process.

Once the computer is able to connect to the 6x2 Matrix for HDMI 4K x 2K,

a removable-disk icon will be displayed under My Computer.

Extract the firmware file from the .ZIP file and drag the .bin file to the Removable Disk.

Disconnect the USB cable from the matrix.

7. The matrix will begin the software upgrade procedure. This process may take a few

minutes.

Do not

disconnect power from the matrix during the upgrade procedure.

Once the firmware upgrade process has completed, the matrix will automatically

reboot.

IMPORTANT:

DO NOT

power-off or disconnect the AC power cord

from the matrix, at any time, during the firmware upgrade process.

Appendix

Firmware Upgrade Procedure

Summary of Contents for ToolBox GTB-HD4K2K-642-BLK



























































































































Search results

Summary of Contents for ToolBox GTB-HD4K2K-642-BLK

Reviews:

Related manuals for ToolBox GTB-HD4K2K-642-BLK

Brands by name

Popular brands

Gefen ToolBox GTB-HD4K2K-642-BLK, User Manual

Search results

Summary of Contents for ToolBox GTB-HD4K2K-642-BLK

Reviews:

Related manuals for ToolBox GTB-HD4K2K-642-BLK

Brands by name

Popular brands