background image

7

14” FLOOR TOM DRUM ASSEMBLY

ITEMS REQUIRED:

1x  Batter Head for 14” Floor Tom Drum 

(with Gear4music logo)

1x  Resonant Head for 14” Floor Tom Drum 

(no logo)

2x  Floor Tom Hoops (14”, attached to drum)

10x  Tom Tension Rods and Washers 

(note – 2x already attached to the drum)

1x Drum Key

1.

   Repeat the steps for the 10” tom tom 

drum assembly.

2.

   Take the 3x fl oor tom legs and insert them into 

the 3x holes on the side of the fl oor tom drum. 
Tighten the wing nuts to secure the legs in 
place. When you put the drum upright on to the 
legs, the Gear4music badge on the side of the 
drum should be straight.

SNARE DRUM ASSEMBLY

ITEMS REQUIRED:

1x Snare Drum (14” x 5.5”)

1x Snare Drum Stand (two parts)

1.

   The snare drum is already assembled but needs 

to be installed on its stand. Take the tripod base 
of the snare drum stand, then unscrew the wing 
nut slightly to release the three arms. Tighten the 
wing nut once the arms are splayed.

2.

   Take the second part of the stand and place the 

pole into the top of the tripod base. Tighten the 
wing nut between both parts to secure in place. 
At the top of the snare drum stand are three 
arms with rubber stops. Evenly space these arms 
and simply set the snare drum on top, with the 
Gear4music logo pointing upwards.

3.

   Push the arms inwards then secure them around 

the drum. Tighten the wing nut on the stand 
(now below the snare drum stand) to secure 
everything into place.

NOTE

 – There is a lever on the side of the 

snare drum. Before beginning to play this 

drum, make sure to push the lever to its 

tensioned position, as this activates the snare 

wire underneath. If you press this lever and 

get no snare sound, you adjust this using the 

knob next to the lever when the tension lever 

is released.

Summary of Contents for BDK-1













Reviews: