background image

2.5.1 General hazard

Source

Consequences

Measures

Faulty valve

Injury and damage

Check that the valve is fully
functional.

Non-compliance with these Op-
erating Instructions

Injury and damage

Read and familiarise yourself
with these Operating Instruc-
tions.

Operating materials

Injuries

Wear personal protective
equipment.

Avoid contact with operating
materials.

2.5.2 Mechanical hazard

Source

Consequences

Measures

Moving or rotating components

Being drawn in or caught

Entrapment

Crushing

Impact

Remove jewellery.

Tie hair back or wear a hair
net.

Wear tight-fitting clothing.

Gravity

Falling objects

Impact

Crushing

Do not walk under suspen-
ded loads.

Eliminate the stumbling haz-
ards.

2.5.3 Electrical hazard

Source

Consequences

Measures

Electromagnetic processes

Implications for electronic medi-
cal implants

People with medical implants
must keep their distance.

Electrostatic processes

Electric shock

Fire

Chemical reaction

Avoid contact to compo-
nents.

Check the voltage of compo-
nents.

Wear personal protective
gear.

Eliminate leaked flammable
substances.

2.5.4 Thermal hazard

Source

Consequences

Measures

Objects or materials at high or
low temperature

Freezing

Burns

Scalding

Wear personal protective
gear.

Wait for adjustment to room
temperature.

16 / 104 - 2.5 General safety instructions

0000000881 - 001 - EN-GB

Summary of Contents for VARIVENT X R Series









































































































Reviews: