GEA FLOWVENT Operating Instruction Download Page 48 | Manualshive

Page: 48 / 84

GEA FLOWVENT Operating Instruction Download Page 48

6.6.1

Fitting to FLOWVENT Valves

Fig.25

Requirement:

•

Pay attention not to kink the air hoses when mounting the control top.

Carry out the following steps:

1.

Insert the O-rings (54) into the upper and lower O-ring groove of the
installation base.

2.

Insert the O-ring (31) on the underside (thread side facing actuator) of the
installation base

3.

Lightly grease the O-rings (54, 31) and the inner thread of the installation
base and then screw the installation base onto the actuator and tighten using
a pin-face spanner and a torque of 20 Nm. When setting the torque heed the
correction factor of the plug tool. If the plug tool (408-451) is used, the torque
to be set is 15 Nm.

4.

Screw switch bar (1) into the actuator and tighten with SW 13, torque 2 Nm
(1.4 lbft).

5.

Fit the control top (B) over the switch bar (1) onto the installation base and
push until stop. For optimum assembly the O-rings (54) should be slightly
greased.

6.

Turn the control top into the required position and tighten the two hexagon
socket screws (51) at the side to 3 Nm (base/ installation base).

Assembly and installation

Mounting the Control Top to FLOWVENT actuators

430BAL014912EN_3

48

25.01.2024

«
...
46
47
48
49
50
...
»

Summary of Contents for FLOWVENT





















































































Reviews:

No comments