manualshive.com logo in svg

GEA FLOWVENT, Operating Instruction, Page: 29 / 84

Share
Download
GEA FLOWVENT Operating Instruction Download Page 29

Technical data: inputs as seen from the AS-interface master

Bit

Function

Signal

DI0*

Feedback
Main stroke

1 = valve in non-actuated
position
0 = valve outside tolerance for
non-actuated position

DI1*

Feedback
Main stroke

1 = valve in actuated position
0 = valve outside tolerance for
actuated position

DI2

 

not assigned

DI3

 

not assigned

* Assignment for green colour variant

Technical data: outputs as seen from the AS-interface master

Bit

Function

Signal

DO0

PV Y1

Activation of solenoid valve Y1

1 = solenoid valve activated
0 = solenoid valve not
activated

DO1

PV Y2

Activation of solenoid valve Y2

1 = solenoid valve activated
0 = solenoid valve not
activated

DO2

PV Y3

Activation of solenoid valve Y3

1 = solenoid valve activated
0 = solenoid valve not
activated

DO3

Reserved for A/B identification

 

ASi light-emitting diode

Technical data

Specification for AS-Interface Adapter Module

430BAL014912EN_3

 

25.01.2024

29

Summary of Contents for FLOWVENT





















































































Reviews:

No comments