background image

Planning Information

3

36"

72"

29-1/2"

Including

Handles

27-1/2"

Case

Depth

716Dia1

PRODUCT DIMENSIONS AND CLEARANCES

These Monogram free-standing refrigerators require the
following clearances for proper air circulation, plumbing
and electrical connections.

Air Circulation Clearances:

• 1/8" on each side
• 1" at the top
• 1-1/2" at the back side

Installation in a corner:

• Allow 4" clearance on each side to an adjacent wall for a

90° opening and access to drawers.

• On the freezer side, allow 14-1/4" min. clearance 

for removal of ice bin.

• On the fresh food side, allow 19" min. clearance 

to wall for removal of drawers.

213Dia11

19"

14-1/4"

160

°

Door Swing

72"

36"

30-1/2"

Including

Handles

28-1/2"

Depth

ZFSB25

ALL MODELS

Z

F

S

B

2

5

Z

F

S

B

2

3

ZFSB23

THE INSTALLATION SPACE

The opening width must be at least 36-1/4".

Water And Electrical Locations 

The opening must be prepared with the electrical and water
supply located as shown.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 
3-prong electrical receptacle recessed into the back wall. 

NOTE:

GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or

through an adjacent cabinet, as close to the back 
wall as possible. The water line should be GE
SmartConnect

Refrigerator Tubing or 1/4" O.D. copper

tubing between the cold water line and water connection
location at the rear of the refrigerator. Installation of an
easily accessible shut off valve in the water line is 
recommended.

Dia6

Wall View

Electrical

Area

73" min.

Water Supply 

36-1/4" min.

Summary of Contents for ZFSB23DSS













Reviews: