manualshive.com logo in svg

GE V7865 Series, Hardware Reference Manual, Page: 18 / 84

Share
Download
GE V7865 Series Hardware Reference Manual Download Page 18

Handling and Installation  17

1 • Handling and Installation

This chapter describes the unpacking procedure; hardware setup; connectors, 
headers and switches; installation; system setup and operation of the V7865.

1.1 Unpacking Procedures 

Any precautions found in the shipping container should be observed. All items 
should be carefully unpacked and thoroughly inspected for damage that might 
have occurred during shipment. The board(s) should be checked for broken 
components, damaged printed circuit board(s), heat damage and other visible 
contamination. All claims arising from shipping damage should be filed with the 
carrier and a complete report sent to GE Intelligent Platforms Customer Care. 

1.2 Handling Precaution 

Electronic assemblies use devices that are sensitive to static discharge. Observe 
anti-static procedures when handling these boards. All products should be in an  
anti-static plastic bag or conductive foam for storage or shipment. Work at an 
approved anti-static workstation when unpacking boards.

1.3 Hardware Setup 

The V7865 is factory populated with user-specified options as part of the V7865 
ordering information. For option upgrades or for any type of repairs, contact 
customer care to receive a Return Material Authorization (RMA).

GE Intelligent Platforms Customer Care is available at: (1-800-433-2682), or

 

+1-780-401-7700 for international calls. 

Or, visit our website at: 

www.ge-ip.com

The V7865 is tested for system operation and shipped with factory-installed 
header jumpers. The physical locations of the jumpers and connectors for the SBC 
with the PMC option are illustrated in Figure 1-1 on page 18. The definitions of 
the connectors, headers and switches are included in Table 1-1 on page 19.

CAUTION

All jumpers marked 

User Configured

 in the following tables may be changed or 

modified by the user. All jumpers marked 

Factory Configured

 should not be 

modified by the user. 

 

 

Care must be taken when making jumper modifications to ensure against 

improper settings or connections. Improper settings may result in damage 

to the unit.

 

 

Modifying any jumper not marked 

User Configured

 will void the Warranty and 

may damage the unit. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for V7865 Series





















































































Reviews:

No comments