GE Simon XT V2 User Manual Download Page 34 | Manualshive

Page: 34 / 40

GE Simon XT V2 User Manual Download Page 34

4. Press Status repeatedly to exit.

Note:

If your system is not connected to a central monitoring station and you do not

have a voice report destination programmed, you won’t be able to perform the
communication test.
If the communication test is successful, the display shows

Comm Test OK

. If the

test is unsuccessful, the Status button will light within 10 minutes and the display
shows

Comm Failure

. If a communication test fails, call your security dealer.

System download

You can initiate a download call to program your system with the settings specified
by your installer. Use this feature only when instructed by your installer or dealer.

To initiate a download:

1. Scroll until the display shows

System Tests

, and then press OK.

The display shows

Enter Code

.

2. Enter your master code, and then press OK.

The display shows

Sensor Test

.

3. Scroll until the display shows

System Download

, and then press OK.

The display shows

Download in Progress

.

Wait while your system calls the download center.
The display will show the result of the download. If the display shows

Download

Fail

, call your security dealer.

4. Press Status twice to exit.

32

Simon XT V2 User Manual

«
...
32
33
34
35
36
...
»

Summary of Contents for Simon XT V2









































Reviews:

No comments