GE SIGNA Voyager Pre-Installation Download Page 129

Page: 129 / 178

Chapter 6 System Interconnections

1 MR System Interconnects Specifications

1.1 Component Designator Definitions

GE Healthcare uses Component Designators to identify system components. All subsystem

cabinets and other components are referred to by their component designators in the

Interconnect Data diagrams and tables.
Table 6-1: MR System Component Designators

Component Designator

Description

CRY

Cryocooler Compressor Cabinet

E01, E02, etc.

Emergency Off Buttons

MDP

Main Disconnect Panel

MAG

Magnet and Enclosure (all magnet enclosure components in Magnet Room)

Modem

Modem for Magnet Monitor

MON

Magnet Monitor

MRU

Magnet Rundown Unit

Operator Workstation

PA1

Pneumatic Patient Alert Control Box

PDU

Power Distribution Unit (PDU) is a module in the ISC cabinet

ISC

Integrated System Cabinet

ICC

Integrated Cooling Cabinet

Patient Transport Table

DS, DS1

Door Switch

Table 6-2: MR System Options Component Designators

Component Designator

Description

OXY

Oxygen Monitor

OM2

Remote Oxygen Sensor Module

MRE

Magnetic Resonance Elastography

SIGNA Voyager Pre-Installation

Direction 5680008–1EN, Revision 2

Chapter 6 System Interconnections

129

Summary of Contents for SIGNA Voyager


















































































































































































Search results

Summary of Contents for SIGNA Voyager

Reviews:

GE SIGNA Voyager, Pre-Installation, Page: 129 / 178

Search results

Summary of Contents for SIGNA Voyager

Reviews: