background image

31-7000091   Rev. 3

5

Installation Instructions

You will find the installation hardware contained in a 

packet with the unit. Check to make sure you have all 

these parts. 

NOTE:

Some extra parts are included.

HARDWARE PACKET

ADDITIONAL PARTS

DAMAGE – SHIPMENT INSTALLATION

If the unit is damaged in shipment, 

return the 

unit to the store in which it was bought for repair or 
replacement. 

If the unit is damaged by the customer,

 repair or 

replacement is the responsibility of the customer. 

If the unit is damaged by the installer

 (if other 

than the customer), repair or replacement must 
be made by arrangement between customer and 
installer. 

Part

Quantity

Wood screws (1/4” x 2”)

2

Toggle bolts (and wind 
nuts) (3/16” x 3”)

2

Self-aligning machine 
screws (1/4” - 28 x 3 
1/4”) 

2

Nylon Grommet (for 
metal cabinets)

1

Tapping screws (for 
attaching the damper 
duct connector)

2-3

One power cord clamp 
and One dark-colored 
mounting screw (to hold 
the power cord)

1

Part

Quantity

Top Cabinet 
Template

1

Rear Wall 
Template

1

Installation 
Instructions

1

Separately 
Packed Grease 
Filter

2

Mounting Plate 
(for supporting 
the microwave 
Oven)

1

Cover plate (for 
Room Venting 
installation) 
included on 
some models

1

PARTS INCLUDED

Summary of Contents for RVM5160MPSA

















































Reviews: