background image

STEP 3 
Weatherproofing

Weatherproof gaps between the exterior and 
interior walls and the case with caulking or 
equivalent weatherproofing material.

NOTE:

* It is critical to caulk around perimeter of wall 

case on all four sides on the outside and the 
roomside where it joins the building to prevent 
air and water infiltration.

For installation in extra thick walls

1. 

If the case is being installed in a thick wall, 
where the case is recessed more than 3”, a case 
extension with splitters aligned with the chassis 
condenser end sheets must be used.

2. 

If the case is being installed in a wall where the 

UHFHVVLVƎRUOHVVDQGDQH[WHQGHGZDOOFDVH

is not used, flashing must be installed under 

WKHFDVHDQGH[WHQGXSƎRQHDFKVLGH7KH

flashing must include a drip rail as illustrated in 
the figure below.

NOTE:

* It is critical to caulk around perimeter of  

wall case on all four sides where it joins the 
building to prevent air and water infiltration.

3

Outdoor 
grille

Drip rail

Case

Caulk*

Flashing

STEP 2 (cont.) 
Installation of the case in the wall opening

3.

 Caulk the entire opening on the outside between 

the case and the building exterior.

4.

 Caulk the entire opening on the inside between  

the case and the building interior.

NOTE:

When using an explosive actuating fastening 
tool, a special nail (Ref. Ramset #1516SD 
drive pin 2-1/2” lg. - 9/64” dia. with 7/8” dia. 
steel washer) should be used. No equipment 
or method should be used that is not in 
compliance with Federal Register Volume 39, 
No. 125 or 
  American National Standard 
  Safety Requirements for Power Actuated 
  Fastening System (ANSIA 10.3-1977) 
Power Level of the case load should not be 
greater than power level 1 identified by a load 
color gray.

Jack stud

Main stud

Wood screw

Molly or toggle bolt

Expansion 
anchor bolt

Power 

activated nail 

(see note)

No holes permitted in bottom of case 
(exception—RAD10 internal drain kit).

Choice of attachment devices through 
both ends of case or the top. Mounting 
screw holes and attachment devices by 
installer.

Outdoor 
grille

Case

Roomside

Steel lintel

Caulk*

Flashing

Drip rail

Caulk*

Caulk*

Finished 
floor or top 
of carpet

Caulk*

Summary of Contents for RAB77B









Reviews: