manualshive.com logo in svg

GE Profile PT920, Technical Service Manual, Page: 40 / 47

Share
Download
GE Profile PT920 Technical Service Manual Download Page 40

– 40 –

Control Board Testing

The resistance of various components can be checked from the Electronic Oven Control by the service 
technician to quickly identify failed or improper operation of certain oven components.

For better clarity, some boards are shown with the top cover removed.

Note

: Colored dots on the relays match the color of the wire. 

Hidden Bake Element

To test the hidden bake 
element from the relay 
board, disconnect the 
orange wire at 

DLB

. The 

resistance should read 
approximately 27 

Ω

 between 

the orange wire at 

DLB

 and 

the yellow wire at 

BAKE

.

 

(See photo.)

Convection Element

To test the convection 
element from the relay 
board, disconnect the 
orange wire at 

DLB

.

 

The 

resistance should read 
approximately 22 

Ω

 between 

the orange wire at 

DLB

 and 

the blue wire at 

CONV

. 

(See 

photo.)

Broil Element

To test the broil element 
from the relay board, 
disconnect the orange 
wire at 

DLB

. The resistance 

should read approximately 
24 

Ω

 between the orange 

wire at 

DLB

 and the purple 

wire at 

BROIL

. 

(See photo.)

Bake

DLB

Conv.

DLB

Broil

DLB

Summary of Contents for Profile PT920
















































Reviews:

No comments