GE Profile PSC25PSWSS Technical Service Manual Download Page 43

Page: 43 / 66

– 43 –

4. Tape the freezer capillary tube 6 inches below

the brazing joint. Score and break the two
capillary tubes below the brazing joints.

Jumper Tube

FF Capillary

Tube

Two Capillary

Tubes

Tape Here

FZ Capillary

Tube

Break

Here

Break

Here

Black
Mark

Brazing

Joints

Common

Tube

Valve Body

Unplug the refrigerator.

2. Remove the rear access cover and evacuate

the sealed system. (See

Evacuation and Charging

Procedure

3. Remove the valve body from the valve coil by

carefully pressing down on top of the valve
body.

Press

Here

(

Continued next page

)

Connect the new jumper tube to the inlet tube of
the new 3-way valve.

6. Prepare the taped capillary tube, and insert

it into the 3-way valve freezer outlet port
(identiﬁ ed with black mark or tape).

7. Prepare the remaining capillary tube and insert

it into the 3-way valve fresh food outlet port.

Fresh Food

Outlet

Black
Mark

Inlet

Freezer

Outlet

Thermal

Paste

Apply a Wet Cloth
to Top of Valve to
Help Keep Valve Cool

Apply a liberal amount of thermal paste to the
base of the three tubes on the new valve. Apply
a wet cloth to the top of the valve to help keep
the valve cool.

Summary of Contents for Profile PSC25PSWSS



































































Search results

Summary of Contents for Profile PSC25PSWSS

Reviews:

Related manuals for Profile PSC25PSWSS

Brands by name

Popular brands

GE Profile PSC25PSWSS, Technical Service Manual

Search results

Summary of Contents for Profile PSC25PSWSS

Reviews:

Related manuals for Profile PSC25PSWSS

Brands by name

Popular brands