GE Profile PSB42LGRBV Technical Service Manual Download Page 7

Page: 7 / 72

– 7 –

Framed Or Custom Panels

Stainless Steel Wrapped Models

42" wide model - PSB42LSRBV

42" wide models - PSB42LGRWV, PSB42LGRBV

Stainless Steel Wrapped Refrigerators

Stainless Steel wrapped refrigerators have
wrapped doors and grille panels, and beveled
edges. These models are shipped ready for
installation.

Door Handles

The handles can be used to accommodate
both framed or custom panels.

Trimmed Refrigerators

Trimmed refrigerators are designed to be
customized with decorative panels. Field
installed custom door and grille panels are

panels from your cabinet manufacturer. The
decorative panel slides into the factory
installed trim. Or, order black and white
accessory panels from your Profile dealer.

Side Panels

Side panels (not supplied) must be used
whenever the sides of the refrigerator will
be exposed.

Accessory Panels

White and black accessory panels are
available from your Profile dealer. Panels are
cut to size and ready to install.

Door Handles

3/4" Custom Panel

24"

*84"

*3" to 4"

1-1/2"

Framed Panel

Door Handles

*Depending on

installation height.

Models

White

Black

Acrylic

PSB42LGRWV

PSPK42DWW

PSB42LGRBV

PSPK42DBB

CUSTOMIZATION BASICS:

Trimmed Models

required. You may install 1/4" thick custom

Summary of Contents for Profile PSB42LGRBV









































































Search results

Summary of Contents for Profile PSB42LGRBV

Reviews:

Related manuals for Profile PSB42LGRBV

Brands by name

Popular brands

GE Profile PSB42LGRBV, Technical Service Manual

Search results

Summary of Contents for Profile PSB42LGRBV

Reviews:

Related manuals for Profile PSB42LGRBV

Brands by name

Popular brands