GE Profile PSB42LGRBV Technical Service Manual Download Page 38 | Manualshive

Page: 38 / 72

– 38 –

Interior Lights

Both the fresh food and freezer interior lights use
120 VAC, 40-watt incandescent bulbs. There are
4 bulbs (160 watts) in the fresh food section, and
2 bulbs (80 watts) in the freezer section.

Freezer bulb voltage is checked at CN07 on the
terminal block. Test for voltage between pin #9
and pin #10.

Note:

Pin #10 is only at neutral when the freezer

door AC switch has closed contacts (door open).

Fresh food bulb voltage is checked at CN09 on
the terminal block. Test for voltage between pin
#4 (neutral) and pin #3.

Note:

Pin #3 is only at line voltage (120 VAC)

when the fresh food AC door switch has closed
contacts (door open).

WARNING:

The center terminal of the freezer

light socket is energized whenever the refrigerator
is plugged in and the main switch is closed,
regardless of door position.

DC Switch

AC Switch

Door Switches

The refrigerator is equipped with an AC and a DC
switch above each door. The switches are located
inside the machine compartment.

AC Switch

DC Switch

Freezer Door

Fresh Food Door

The AC switch, above the freezer door, controls
the freezer interior lights and the auger motor
operation. The freezer light is switched through
the neutral side of the line.

The AC switch, above the fresh food door,
controls the fresh food interior lights.

CN08

PURPLE/BLUE

YELLOW

ORANGE

BLACK

10

11

12
13

RED

NEUTRAL

AUGER MOTOR

FRESH FOOD LIGHT

FREEZER LIGHT

LINE (L1)

FREEZER DOOR SWITCH

FRESH FOOD

DOOR SWITCH

AC DOOR SWITCHES

The DC switches provide “door open” information
to the power control board (PCB).

Note:

The

fans turn off when the doors are

opened (DC door switches control operation)
and delay 10 seconds before restarting when the
doors are closed again. The freezer door switch
controls only the freezer fan. The fresh food door
switch controls both the fresh food and freezer
fan operation.

CN02

WHITE/YELLOW

WHITE/BLUE

GRAY

FREEZER DOOR

SWITCH

6
7

13

FRESH FOOD

DOOR SWITCH

DC DOOR SWITCHES

«
...
36
37
38
39
40
...
»

Summary of Contents for Profile PSB42LGRBV









































































Reviews:

No comments

Related manuals for Profile PSB42LGRBV

Brand: Haier Pages: 23

Brand: Haier Pages: 88

Brand: Haier Pages: 7

Brand: Gamko Pages: 88

Brand: U-Line Pages: 12

Brand: U-Line Pages: 24

Brand: Samsung Pages: 42

Brand: Saivod Pages: 52

Brand: True Pages: 2

Brand: ZANKER Pages: 18

Brand: Inoksan Pages: 42

Brand: Jacky's Pages: 40

Brand: True Pages: 2

Brand: Giostyle Pages: 96

Brand: Samsung Pages: 34

Brand: Samsung Pages: 136

Brand: Danby Pages: 48

Brand: Danby Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands