GE Profile PSB42LGRBV Technical Service Manual Download Page 4

Page: 4 / 72

– 4 –

Introduction

The new Proﬁ le Built-In Side by Side refrigerator has the following features:

Separate freezer and fresh food evaporators are recessed into the machine compartment for
increased efﬁ ciency and interior space savings.

3-Way valve directs refrigerant ﬂ ow where needed.

High-and low-side sealed system mufﬂ ers quiet the operation.

Inverter is built into the power control board (PCB).

Combined dispenser and temperature control board provides customer control and test mode
operations.

Dispenser cube motor and cam replaces solenoid-operated cube mechanism.

Room ambient thermistor aids power control board (PCB) operation.

Component electrical testing is performed at the machine compartment-mounted terminal block.

Rear leveling mechanism is front-adjustable.

•

Summary of Contents for Profile PSB42LGRBV









































































Search results

Summary of Contents for Profile PSB42LGRBV

Reviews:

Related manuals for Profile PSB42LGRBV

Brands by name

Popular brands

GE Profile PSB42LGRBV, Technical Service Manual

Search results

Summary of Contents for Profile PSB42LGRBV

Reviews:

Related manuals for Profile PSB42LGRBV

Brands by name

Popular brands