background image

18

About water softener system.

Service: Manually Initiated Electronic Diagnostics

To enter diagnostics, press and hold the 

DATA

button until the display appears as shown.

NOTE: 

If the softener is in the middle of a regeneration, top part of the display shows the cycle 

of regeneration and minutes of the cycle remaining. If two cycle names are flashing, the valve 
is in transition between the cycles.

A

The three digits under 

WATER MANAGEMENT SYSTEM 

indicate water meter operation 

as follows:

000 (steady) = soft water not in use…no flow through the meter.

—OPEN A NEARBY SOFT WATER FAUCET—

000 to 140 (continual) = repeats display for each gallon of water passing through the meter.

If you don’t get a reading in the display, with faucet open, pull the sensor from the valve outlet
port. Pass a small magnet back and forth in front of the sensor. You should get a reading in the
display. If you get a reading, shut off water supply, unhook the in and out plumbing and check the
turbine for binding.

This display segment (

), in the following chart, indicates an open POSITION switch. 

Use the 

TOUCH or HOLD

button to manually advance the valve into each cycle and check correct

switch operation.

1

CORRECT SWITCH

DISPLAYS

VALVE CYCLE STATUS

Valve in service, fill, brining, backwash
or fast rinse position.

Valve rotating from one position to another.

Press the 

DATA

button again. This diagnostic display shows the total number of recharges (top)

since the timer was connected to electrical power.

The number of days since the timer was connected to electrical power is shown in the bottom part
of the display. If over 1999 days, a (x10) indicator shows, meaning you must multiply the number
shown by 10.

Press 

DATA

once again to return the present time to the display.

3

2

RECHARGE

WATER MANAGEMENT SYSTEM

DAY

x 10

LAST RECHARGE

On

WATER MANAGEMENT SYSTEM

Turbine

TIME

Fill

WATER MANAGEMENT SYSTEM

Turbine

Switch

Turbine

count

Valve

Minutes of cycle

position

remaining

Motor

Turbine

Turbine
support
& shaft

Position

switch

Valve
outlet

Sensor
housing

Summary of Contents for PNSF39Z01





































Reviews: