GE PCIE-5565PIORC* Hardware Reference Manual Download Page 39

Page: 39 / 70

Programming 39

Table 3-26 Power Management Capability Structure

Offset

31::24

23::16

15:8

7:0

0x078

Capabilities Register (Hardwire to 0x0003)

0x80 Next Cap Ptr

0x01 Capability ID

0x070

Data (hardwired to 0x00)

PM Control/Status Bridge
Extensions (hardwired to
0xx00)

Power Management Status and Control

(hardwired to 0x0008)

Table 3-27 PCIe Capability Structure

Offset

31::24

23::16

15:8

7:0

0x080

PCI Express Capabilities Register

0x00

0x10 Capability ID

0x084

Device Capabilities

0x088

Device Status

Device Control

0x08C

Link Capabilities

0x090

Link Status

Link Control

Table 3-28 PCIe Capabilities Register Bit Definition

PCIe Capabilities Register Bit Definition: Offset 0x082

Bit(s)

Field

Description

R/W

15:14

Reserved

13:9

Interrupt Message
Number

Not Supported. Hardwired to 0

Slot Implemented

Not Supported. Hardwired to 0

7:4

Device/Port type

Indicates the PCIe logical device type.
- 0001:Legacy PCI Express Endpoint

3:0

Capability Version

- 0x1

Table 3-29 Device Capabilities Register Bit Definition

Device Capabilities Register Bit Definition: Offset 0x084

Bit(s)

Field

Description

R/W

31:28

Reserved

27:26

Captured Slot Power
Limit Scale

Not Applicable to endpoint. Hardwired to 00 R

25:18

Capture Slot Power
Limit Value

Not applicable to endpoint. Hardwired to
00011001

17:15

Reserved

- 001

Power Indicator
Present

Not Supported. Hardwired to 0

Attention Indicator
Present

Not Supported. Hardwired to 0

Attention Indicator
Button Present

Not Supported. Hardwired to 0

11:9

Endpoint L1
Acceptable Latency

000 (less than 1 micro seconds)

8:6

Endpoint L0
Acceptable Latency

000 (less than 64 nano seconds)

Extended TAG Field
Supported

5-bit Tag field supported
0

Summary of Contents for PCIE-5565PIORC*







































































Search results

Summary of Contents for PCIE-5565PIORC*

Reviews:

Related manuals for PCIE-5565PIORC*

Brands by name

Popular brands

GE PCIE-5565PIORC*, Hardware Reference Manual

Search results

Summary of Contents for PCIE-5565PIORC*

Reviews:

Related manuals for PCIE-5565PIORC*

Brands by name

Popular brands