NX-8E CONTROL
25
LOCATION 47 - AUXILIARY OUTPUT #1, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Use the chart on page 25 to select the event that will activate Auxiliary Output 1.
Segment 2:
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 1, Location 46). Programming a "0" makes the output follow the event.
LOCATION 48 - AUXILIARY OUTPUT #2, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Use the chart on page 25 to select the event that will activate Auxiliary Output 2.
Segment 2:
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 2, Location 46). Programming a "0" makes the output follow the event.
LOCATION 49- AUXILIARY OUTPUT #3, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Use the chart on page 25 to select the event that will activate Auxiliary Output 3.
Segment 2:
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 3, Location 46). Programming a "0" makes the output follow the event.
LOCATION 50- AUXILIARY OUTPUT #4, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Use the chart on page 25 to select the event that will activate Auxiliary Output 4. .
Segment 2:
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 4, Location 46). Programming a "0" makes the output follow the event.
Table XI-1 AUXILIARY OUTPUT EVENT SELECTION
DATA
EVENT
DATA
EVENT
DATA
EVENT
0
/
Burglary Alarm
18 Entry
36 Telephone Line Fault
1
/
Fire Alarm
19 Exit
37 Program Mode
2
/
24 Hour Alarm
20 Entry or Exit
38 Download In Process
3
/
Trouble Alarm
21 Armed State
39 Ground Fault
4
/
Tamper Alarm
22 Disarmed State
40 Short Circuit (Over-current)
5
Yelping Siren (Burglary)
23 Ready
41 Box Tamper
6
Temporal Siren (Fire)
24 Not Ready
42 Siren Tamper
7
Any Siren
25 Fire
43 Any Open
8
Any Bypass
26 Fire Trouble
44 Any Short
9 AC Fail
27
Chime
45
Any Fault (Open/ Short on
Non-Fire Zone)
10 Low Battery
28
/
Expander Trouble
46
/
Any Alarm
11
/
Duress
29 Dynamic Battery Test Time
47 Beeping Keypad
12
/
Aux 1 Keypad Zone
30 Open Period
48
/
Code Entry (See note below)
13
/
Aux 2 Keypad Zone
31 Closed Period
49
˜
/
Key FOB Function 1
14
/
Panic Keypad Zone
32 Listen-In
50
˜
/
Key FOB Function 2
15 Keypad Tamper
33 Line Seizure
69
Forced Door Alarm
16
/
Autotest
34 Ground Start
70
Forced Door Restore
17 Alarm Memory
35 Fail To Communicate
˜
Events 49 & 50 require NX-408, NX-416, or NX-448 wireless receivers to operate.
/
If set to follow condition, these events will be 1 second.
Notes: When Event 48 is programmed, it is possible to program a user code's authorization to select which output(s)
a particular code will activate. When LED 8 is on for an authorization, then LEDs 1- 4 correspond to that code
activating outputs 1 - 4 respectively. (See programming the LED keypads on page 8.)