![background image](http://html.mh-extra.com/html/ge/multilin-269-motor-management-relay-series/multilin-269-motor-management-relay-series_instruction-manual_131870048.webp)
Actual Values, Pg. 2
3 SETUP AND USE
Page
Line
Information Line
Description
3-9
2
11
•
RTD TEMPERATURE
RTD TEMPERATURE
RTD #8= XXX DEGREES C
RTD #8= XXX DEGREES C
or
AMBIENT TEMPERATURE
AMBIENT TEMPERATURE
RTD #8= XXX DEGREES C
RTD #8= XXX DEGREES C
RTD #8 temperature.
Seen when RTD #8 is used for ambient sens-
ing on model 269
12
•
MAX. STATOR SINCE LAST
MAX. STATOR SINCE LAST
ACCESS: RTD# X = XXX
ACCESS: RTD# X = XXX
Maximum stator RTD temperature since last
access.
13
•
MAXIMUM RTD#7 TEMP SINCE
MAXIMUM RTD#7 TEMP SINCE
LAST ACCESS: XXX DEGREES C
LAST ACCESS: XXX DEGREES C
Maximum RTD #7 temperature since last ac-
cess.
14
•
MAXIMUM RTD#8 TEMP SINCE
MAXIMUM RTD#8 TEMP SINCE
LAST ACCESS = XXX C
LAST ACCESS = XXX C
Maximum RTD #8 temperature since last ac-
cess.
15
•
CLEAR LAST ACCESS DATA?
CLEAR LAST ACCESS DATA?
XXX
XXX
Used to clear the data in the last 5 lines (see
section 3.1, STORE key).
16
END OF PAGE TWO
END OF PAGE TWO
ACTUAL VALUES
ACTUAL VALUES
Last line of page 2.
In the above messages, temperatures may be displayed in either Celsius (indicated by “C”) or Fahrenheit (indicated
by “F”) depending on the setting in Setpoints pg.2 line 2.
•
Lines 3 to 15 in the above messages are not shown if the answer to the question “ARE THERE ANY RTDs
CONNECTED?” is “NO”. This setpoint is located on page 2 of Setpoints, line 3.
Summary of Contents for MULTILIN 269 MOTOR MANAGEMENT RELAY Series
