8
49-3000198-1
Settings
Individual settings for cycle minutes (
Time
), dryness level (
Level
) and temperature (
Temp
) can be set from the
minimum (lowest in column) to maximum (highest in column). In general, the higher up the column, the more
energy will be used.
NOTE:
The selected cycle set
Time
can be further adjusted, in one minute increments, by
pressing the
More Time
and
Less Time
buttons.
H
I
G
Getting started
USING THE DR
YER
Dryness Level -
Selection only used for Sensor cycles. Timed cycles run for the selected time.
More Dry
Use for heavy-duty or mixed type fabrics.
Dry
Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy savings.
Less Dry
Use for lighter fabrics.
Damp
For leaving items partially damp.
Temperature
High
For regular to heavy cottons.
NOTE: STEAM Dewrinkle
and
STEAM Refresh
require the High temperature setting.
Medium
For synthetics, blends, delicates and items labeled permanent press.
Low
For delicates, synthetics and items labeled tumble dry low.
No Heat
For fluffing items without heat. For use only with the
AIR FLUFF
cycle.
Wrinkle Care
Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are dry. If
you are using the cycle
Sound
and you select the
Wrinkle Care
option, a signal will sound at the end of the drying
time and several times during the
Wrinkle Care
cycle. This will remind you that it is time to remove the clothes.
Damp Alert
(on some models)
This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang
dry. The
Damp Alert
will only beep when this option is selected (but the dry cycle will keep running). Removing clothes
and hanging them when they are damp, can reduce the need to iron some items. The light beside the button will be
lit when
Damp Alert
is on.
Drum Light
The drum light will turn on if, the
Damp Alert
button or the
Sound
button (depending on model) is pressed for
3 seconds, or the door is opened. It will turn off when the door is shut, the
Damp Alert
button or
Sound
button
(depending on model) is pressed again for 3 seconds or after 5 minutes if the door is left open.
Delay Dry
Press the
Delay Dry
button to set the delay start time in 1 hour increments up to 24 hours, and then back to clear (0
hours). After selecting the delay start time, press
Start
and the delay time will count down the time remaining until the
cycle starts.
NOTE:
To set the amount of delay time faster, you can press and hold the
Delay Dry
button.
Delay Dry for WiFi Connected Dryers
For more information see the
Appliance Communication
section.
You have two options to set
Delay Dry
using your smartphone.
Option 1:
Follow
Delay Dry
instructions. You can use the
GE Appliances
Laundry App to adjust the amount of
time via your smartphone.
Option 2:
Set your dryer to “AP” using the
Delay Dry
button. This allows you to use the
GE Appliances
Laundry
App via your smartphone to start your dryer remotely at the time of your choosing. If the dryer is set to AP with no
activity, it will start the dryer 24 hours later.
Sound
Use the
Sound
button to change the volume of the button presses and the end of cycle signal. Press the button until
you reach the desired volume or off. The clothes should be removed when the end of cycle signal goes off so wrinkles
do not set in.
NOTE:
• Remove garments promptly at the sound of signal. Place clothes on hangers so wrinkles will not set in.
• Use the
Sound
especially when drying fabrics like polyester, knits and permanent press. These fabrics should be
removed so wrinkles will not set in.
My Cycle
As the cycle selector knob is turned, the
Time
(timed dry),
Level
(dryness level) and
Temp
(temperature)
settings change to automatic pre-set default settings. If you desire a different setting, press the appropriate button(s).
Then press and hold the
My Cycle
button for 3 seconds and the dryer will “remember” these settings for that
Knob Selection. In the future, when you turn the selector knob to that cycle, your settings will be automatically
recalled.
NOTE:
Signal sound cannot be set for
My Cycle
.
