background image

OPEN

GAS VALVE.

APPLY PIPE COMPOUND

TO ALL MALE THREADS.

Tighten all connections using two adjustable wrenches.

Do not overtorque gas connections!

APPLY PIPE COMPOUND

TO THE ADAPTER AND

DRYER GAS INLET.

NEW METAL

FLEXIBLE GAS

LINE CONNECTOR

ADAPTER

ELBOW

ITEMS NOT SUPPLIED

ADAPTER

SHUT-OFF

VALVE

PIPE SIZE

AT LEAST 1/2"

1/8" NPT PIPE

PLUG FOR

CHECKING GAS

INLET PRESSURE

3/8" NPT

Tighten the flexible

gas line using two

adjustable wrenches.

Installation Instructions

3 RECONNECTING GAS

3

       

WARNING - NEVER USE AN OPEN

FLAME TO TEST FOR GAS LEAKS.

4 LEAK TEST

Check all connections for leaks with soapy solution or equivalent.
Apply soap solution. 

Leak test solution must not contain ammo-

nia which could cause damage to the brass fittings.

 If leaks are

found, close valve, retighten the joint, and repeat the soap test.

Note:  The connector and fittings are designed for use only on the 
original installation and are not to be reused for another appliance 
or at another location.  Keep flare end of adaptor free of grease, oil 
and thread sealant.
Caution:  Use adapters as shown.  Connector nuts must not be 
connected directly to pipe threads.  

Listed connector ANSI Z21.24 / CSA 6.10

Summary of Contents for DBVH520GJ















Reviews: