background image

Electrical 

Use of adapter plug

IMPORTANT...

Because of potential safety

Please Read Carefully.

hazards under certain conditions,
we strongly recommend against

How to connect electricity

the use of an adapter plug.
However, if you still elect to use an

For personal safety, this

adapter, where local codes permit,

appliance must be properly

a TEMPORARY 

grounded.

may be made to a properly grounded

 wall outlet 

 use of a

Electrical requirements

 models require a 115/120

volt 

 60 

 grounded outlet

protected with a 15 amp time delay
fuse or circuit breaker.

The power cord of this appliance
is equipped with a three-prong

 plug which mates with

a standard three-prong (grounding)
wall outlet (Fig. 1) to minimize the
possibility of electric shock hazard
from this appliance.

PREFERRED ,
METHOD

 - 

INSURE PROPER

 EXISTS

BEFORE USE

 /~

Have the wall outlet and circuit
checked by a qualified electrician
to make sure the outlet is properly
grounded.

Where a standard two-prong
wall outlet is encountered, it is
your personal responsibility and
obligation to have it replaced with
a properly grounded three-prong
wall outlet.

DO NOT, 

 ANY

CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.

 fisted-adapter (Fig. 

-

2) available

at most local hardware stores.

TEMPORARY METHOD

The larger slot in the adapter must
be aligned with the larger slot in
the wall outlet to provide proper
polarity in the connection of the
power cord.

CAUTION: Attaching an adapter
ground terminal to wall outlet cover
screw does not ground appliance
unless cover screw is metal, and
not insulated, and wall outlet is
grounded through house wiring. You
should have circuit checked by a
qualified electrician to make sure
the outlet is properly grounded.

When disconnecting the power
cord from the adapter, 
always
hold the adapter with one hand. If
this is not done, the adapter ground
terminal is very likely to break with
repeated use.

Should the adapter ground

 break, 

 

 USE the

appliance until a proper ground
has again been established.

Use of 

 cords

not recommended

Because of potential safety
hazards under certain conditions,
we strongly recommend against
the use of an extension cord.
However, if you still elect to use
an extension cord, it is absolutely
necessary that it be a 

 listed

3-wire grounding type appliance
extension cord having a grounding
type plug and outlet and that the
electrical rating of the cord be 15
amperes (minimum) and 120 volts.

(continued next page)

9

Summary of Contents for AVS06













Reviews: