© 2005 GE Security B.V.
MAINST-ATS1190
All rights reserved
09/2005
ATS1190 ATS1192
Smart Card Reader
I
NTRODUCTION
The ATS1190/1192 Smart Card Reader is a multifunction, all-
purpose proximity card reader suitable for all locations requiring a
short-range reader. The reader can be connected directly to the
ATS Control Panel (see figure
Y
). It is configurable through a
Menu system accessible via the BUS or by Configuration cards
programmed through Titan and the Smart Card Programmer
(ATS1621/22) or the ATS1481 Programming card.
The reader operates from 9 to 14 VDC. It has a quiescent current
consumption of less than 25 mA and less than 80 mA when
reading a card. The ATS1190 is supplied standard with a white
removable dress cover, which can be interchanged with one of
four other colours available.
The ATS1192 is a heavy-duty version designed for standard door
frames.
Both the ATS1190 & ATS1192 are waterproof.
Figure
: Smart Card Reader
Blue LED:
Door open
Red LED:
Door open
Disarmed
Armed
M
OUNTING
The reader can be mounted on any flat surface by two pan head
screws, 3.0-3.5 mm diameter, located under the dress cover. A
slightly reduced range will be experienced when mounted on metal
surfaces. If mounting in an outdoor environment, ensure that the
blue LED is at the top.
It is not recommended to use countersunk screws.
For the ATS1190 the dress cover can be removed to expose the
mounting screw by gently prizing the sides away from the main
body to release the retaining clips and gently pulling on the
connection cord. Do not use excessive force or the reader can be
irreparably damaged.
After mounting, gently press the cover over the main body until it
locks into place.
RAS
ADDRESSING
The address of the reader for BUS operations is set to the default
address RAS 16. Using a configuration card or accessing its on-
line Menu system when connected to the RS485 BUS can change
this. See the Programming Guide, Reader Address, for further
details.
T
AMPER
The reader is provided with a Tamper facility. When connected to
the BUS, Tamper data is transmitted to the Advisor Master with
system data. An external Open Collector output (violet wire) can
be configured as a Tamper control for both online and offline
operation.
R
EADER WIRING
Red:
Positive 9 to 14 VDC supply
Black: 0 Volts
DC supply ground
Green: D0 / D-
Clock
RS485 Data - Wiegand Data 0
Absolute maximum, 12 V @ 10 mA
White: D1/ D+
Data
RS485 Data + Wiegand Data 1
Absolute maximum, 12 V @ 10 mA
Brown: LED
1 Offline LED control configured to "Two Wire
Control" will control the red LED only
Wire grounded: Red LED on
Wire open: Red LED off
Wire at +5 V to +12 V: Red LED off or, offline
LED control configured to "One Wire Control"
will control both the red and blue LED’s
Wire grounded: Blue LED on
Wire open circuit: Both LED’s off
Wire at + 5 V to 12 V: Red LED on
Absolute maximum, 14 V
ATS1190/1192
Smart Card Reader
ATS1190/1192 ATS1105 ATS1170 ATS2000/3000/4
000
ATS1250/1260 ATS1250/1260
localbus
Cable
J2
J1
J1
Door 1, 2, 3, 4
Comms
Red 12V
12V 12V
12V
12V
Black 0V 0V
0V
0V
0V
Green D0 D0
D-
D0
D-
White D1 D1
D+
D1
D+
Yellow - L2
-
L2
-
Brown - L1
-
L1
-
Blue - BZ -
BZ
-
Violet - -
-
With 4K7 (in series)
to Alarm Input 3
-
Y
Summary of Contents for ATS1192
Page 12: ......
