background image

The ceiling bracket must be installed when the duct
cover is used to span 24” or more height above the
hood. The bracket will hold the decorative duct cover in
place at the top.

Note:

The ceiling bracket is not required when using

only the 12” section of the duct cover.
• Install the 2 small screws into the sides of the duct

bracket. Remove the screws. Pre-tapping the holes will
insure ease of final installation.

• Match center notch on the bracket to the centerline

on the wall and flush against the ceiling.

• Mark the 2 screw hole locations.
• Drill 1/8” pilot holes in marked bracket location.
• If pilot holes do not enter studs, enlarge the holes to

3/8” and install wall fastener anchors.

• Secure the bracket to the rear wall with wood screws

and washers. Use wall anchors if needed.

Note:

Bracket has 2 sets of holes. Use larger holes for wall

fasteners or wood screws with washers. Use smaller holes
for wood screws with washers.

INSTALL CEILING BRACKET

Installation Instructions

16

5

Install Ceiling

Bracket When

Duct Cover is
Used to Span

24” or more

See Step 9

to Install

Duct Cover

1 Ft = 0.3 m
1” = 2.5 cm

CONNECT DUCTWORK

6

• Push duct over the end of the transition until it

reaches the stop tabs.

• Install ductwork, making connections in direction of

airflow as illustrated.

• Secure joints in ductwork with sheetmetal screws.
• Wrap all duct joints with duct tape for an airtight seal.
• Use duct tape to seal the flange connection.

Duct Tape

Over Seam

and Screw

Duct Tape

Duct Tape

Over Flange

Screw

Duct

Stops

Air Flow

CAUTION:

Do not use sheet metal screws at the hood flange
connection. Doing so will prevent proper damper
operations. Seal connection with tape only.

Summary of Contents for Appliances CV936

























Reviews: