background image

When necessary, the hood may be installed so that it is
supported by the soffit.
• The soffit should be constructed with 2 x 4’s.
• Determine the installation location.
• Continue the centerline forward on the bottom of the

cabinet or soffit.

Alternate Mounting Method

INSTALL HOOD TO SOFFIT OR

BENEATH CABINETS

Installation Instructions

15

4

IMPORTANT: Framing must be capable of

supporting 100 lbs (45.3 kg)

• Mounting screws must be secured to 2 x 4 studs 

(Dim. “A”) at locations shown in the above chart.

• Allow minimum opening (Dim. “B”) to accommodate

the duct transition in the soffit.

Cut a 10¾” x 8-7/16” hole through bottom of soffit or cabinet
for duct transition as shown.

B

A

A

C

2-3/8"

8-7/16"

5-3/8"

5-3/8"

Rear Wall

1 Ft = 0.3 m

1” = 2.5 cm

7-1/16"

14-1/2"

C

14-1/2"

12"

29-7/8"

2-9/16"

2-1/4"

2-3/8"

8-7/16"

10-3/4"

IMPORTANT: For additional support and to minimize
vibration during operation, we strongly recommend that
the hood also be secured to the back wall with wall
fasteners.

Top View, Front Side

30” Models

• Drill four 1/8” pilot holes in locations shown.
– If mounting to the underside of a cabinet with a

recessed bottom, install shims to fill the gap.

SKIP THIS STEP IF USING WALL MOUNTING

METHOD

“A”

“B”

Centerline to

Opening

Center of Stud

For Ductwork

30” Models

14½”

10¾”W x 8-7/16”D

36” Models

17½”

10¾”W x 8-7/16”D

Top View, Front Side

7-1/16"

17-1/2"

C

17-1/2"

12"

35-7/8"

2-9/16"

2-1/4"

2-3/8"

8-7/16"

10-3/4"

Top View, Front Side

36” Models

• Drive mounting screws into the studs until they

protrude ¼”. This ¼” gap will provide clearance to
engage the keyhole slots in the top of the hood.

• Lift hood onto mounting screws. Slide back against

the rear wall.

• Pull house wiring through the knockout at the rear or

the top of the hood.

• Tighten mounting screws.

Transition

Cabinet or

Soffit

¼” Gap

Add Shims
If Bottom Is
Recessed

Back Wall

Engage Keyhole
Slots and Push
Back to Wall

Summary of Contents for Appliances CV936

























Reviews: