background image

 

● 

The cabinet maybe installed through the wall in

both existing buildings and new construction.

● 

The side louvers must project on the outdoor

side of the wall.

● 

The room side of the cabinet must project into

the room at least 1“ from the finished wall.

● 

The cabinet must be installed level from side to

side and with a 3/8” tilt from front to rear.

See page  8.

 MATERIALS 

(obtain 

● 

wood screws, 1“ long

● 

10 # 10 wood screws, 1“ long

● 

1 tube high grade caulking compound

● 

Lintel, if required, to support bricks or blocks

above opening.

 PREPARE WALL OPENING

1. Determine size of opening. Measure width

and height of cabinet and add 1/8” to each
dimension.

AEM09 dimensions

 AEM 

14, 

AEM 

 AEM 18 DA, 

 dimensions

2.  Choose the wall opening location.  Be sure

wall receptacle is (or will be) installed nearby.

3.  Make the opening. Frame it to support the

weight of the air conditioner. Add metal flashing
over bottom of frame opening and 1“ up  on sides
to reduce the possibility of condensate entering
the area between the inner and outer wall.

2. 

PREPARE THE CABINED

 Remove chassis from cabinet.

2. With caulking compound or electrical tape, seal

10 holes provided in cabinet for top rail and side

retainers not used in this installation. *

* Remove side retainers for AEM09 models.

12

Summary of Contents for AED22

















Reviews: