background image

 

Programming 

FireShield Technical Reference Manual 

 

3.13 

3.  Press Reset to select tone or pulse dialing for line 2. 

4.  Press Panel Silence to save and advance to the next 

program option. 

 

The trouble buzzer sounds a long beep as confirmation. 

22. Select AC fail delay time 

Description: The AC fail delay lets you set the amount of time 
before the panel signals that it is operating with insufficient or 
no AC power. 

Settings: 6 hours (central station) 
 

15 hours (remote station) 

Default: 6 hours 

To select the AC fail delay time: 

1.  Press Reset to select the desired AC fail delay time. 

2.  Press Panel Silence to save and advance to the next step. 

 

The trouble buzzer sounds a long beep as confirmation. 

23. Enter the transmission test time 

Description: Specifies the time of day the transmission test 
message is sent to the CMS. Values are in 24-hour time. 

Format: 0000 – 2359 

Default: 0217 

To enter the transmission test time: 

1.  Press Reset to enter the hour. 

2.  Press Panel Silence to save. 

 

The trouble buzzer sounds a long beep as confirmation. 

3.  Press Reset to enter the minutes. 

4.  Press Panel Silence to save and advance to the next 

program option. 

 

The trouble buzzer sounds a long beep as confirmation. 

24. Select the transmission test frequency 

Description: Specifies the number of days between sending a 
transmission test message to the CMS. 

Note: 

NFPA 72 and UL 864 require daily tests for commercial 

systems. 

Settings: 0  =  None 
 1 

Daily 

 

2 = 30 days 

Default: 1 (daily) 

To select the transmission test frequency: 

1.  Press Reset to select the transmission test frequency. 

2.  Press Panel Silence to save and advance to the next step. 

 

The trouble buzzer sounds a long beep as confirmation. 

25. Enter the number of rings to answer 

Description: Sets the number of rings that are ignored before 
answering an incoming modem call. 

Settings: 0 – 15 rings 

Default: 5 (rings) 

To enter the number of rings: 

1.  Press Reset to change the number of rings to answer. 

2.  Press Panel Silence to save and advance to the next 

program option. 

 

The trouble buzzer sounds a long beep as confirmation. 

26. Select the ring type 

Description: Specifies the type of ring expected when an 
incoming call is received. 

Default: Ring type (additional options to be added in future 
release). DACT answers any ring type after programmed ring 
count. 

To select the ring type: 

1.  Press Reset to select ring type. 

2.  Press Panel Silence to save and advance to the next step. 

 

The trouble buzzer sounds a long beep as confirmation. 

27. Enable (disable) call back 

Description: Call back adds increased security when uploading 
or downloading. When an incoming call is received on line 
one, the panel establishes a connection and waits for a valid 
password. If call back is not enabled, uploading or 
downloading begins. If call back is enabled, the panel 
disconnects the incoming call and dials the programmed call 
back number. Once the connection is reestablished, uploading 
or downloading can begin. 

Settings: No 
 Yes 

Default: No 

To enable (disable) call back: 

1.  Press Reset to select enable (disable) call back. 

2.  Press Panel Silence to save and advance to the next 

program option. 

 

The trouble buzzer sounds a long beep as confirmation. 

Summary of Contents for FireShield FS302





































































Reviews: