GE Multilin 469 Instruction Manual Download | Manualshive

Page: 177 / 338

background image

CHAPTER 5: SETTINGS

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

5–35

For example, serious trips such as Short Circuit and Ground Fault may be assigned to the
2 AUXILIARY relay so that they can only be reset via the remote reset terminals (D18 and
D23) or the communication port. The remote reset terminals should be connected to a
keyswitch so that only authorized personnel could reset such a critical trip.

• Assign only Short Circuit and Ground Fault to the 2 AUXILIARY relay
• Program

2 AUXILIARY

to “Remote Reset Only”

5.5.3

Force Output Relay

PATH: SETTINGS

ZV

S4 OUTPUT RELAYS

ZV

FORCE OUTPUT RELAYS

The output relays can be independently forced in static or dynamic mode. In static mode
the selected relay will operate as long as it is in the “Enabled” state. Only when the user
enters “Disabled” will the selected relay reset. In dynamic mode the user specifies the
operate time (1 to 300 seconds) and the selected relay will operate for the specified
duration.

The

FORCE OUTPUT RELAY

option is NOT allowed when the selected relay output is already

active due to trip or alarm condition, when the 469 is in start block condition, or when the
469 is not in service.

Note

IMPORTANT NOTE

: The forced relay will override any trip or alarm conditions. (i.e. when the

relay is forced and trip occurs, the relay will still be enabled when the trip condition is reset).

Control power loss in the 469 will

reset

all forced relays.

FORCE

[

FORCE 1 TRIP

RELAY: Disabled

Range: Disabled, Enabled

MESSAGE

FORCE TRIP RELAY

DURATION: Static

Range: Static, 1 to 300 s in steps of 1

MESSAGE

FORCE 2 AUXILIARY

RELAY: Disabled

Range: Disabled, Enabled

MESSAGE

FORCE 2 AUX RELAY

DURATION: Static

Range: Static, 1 to 300 s in steps of 1

MESSAGE

FORCE 3 AUXILIARY

RELAY: Disabled

Range: Disabled, Enabled

MESSAGE

FORCE 3 AUX RELAY

DURATION: Static

Range: Static, 1 to 300 s in steps of 1

MESSAGE

FORCE 4 ALARM

RELAY: Disabled

Range: Disabled, Enabled

MESSAGE

FORCE ALARM RELAY

DURATION: Static

Range: Static, 1 to 300 s in steps of 1

MESSAGE

FORCE 5 BLOCK

START

Range: Disabled, Enabled

MESSAGE

FORCE BLOCK RELAY

DURATION: Static

Range: Static, 1 to 300 s in steps of 1

«
...
175
176
177
178
179
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Eaton Pages: 29

Brand: Eaton Pages: 621

Z-one ZSR101 Series

Brand: CALEFFI Pages: 52

Brand: Elko Pages: 2

Brand: 6TL Pages: 25

Brand: Gewa Pages: 12

Brand: Schweitzer Engineering Laboratories Pages: 468

Brand: Tri-M Systems Pages: 35

Brand: ASO Safety Solutions Pages: 6

Brand: Zennio Pages: 2

Brand: GE Pages: 78

Brand: GMI Pages: 5

Brand: Zamel Pages: 4

Brand: Arcteq Pages: 369

950-1040 24V RELAY KIT 8504052 REV. 3 1097

Brand: TJERNLUND Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands