![background image](http://html1.mh-extra.com/html/gbc/autoultima-pro/autoultima-pro_instruction-manual_3901911005.webp)
5
G
Location of controls
1
Feed Tray
2
Paper Side Guide
3
Top Cover
4
Control Panel
5
Exit Tray
6
Power Button
7
4 EZ Load Levers
8
Heat Button
9
Feed Switch
J
Idler Bar Assembly
K
Heat Shoe
L
Film Roll
M
Power LED (Red)
N
Ready LED (Green)
O
Scroll Button
Perform only the routine maintenance procedures referred to in these
instructions.
Do not attempt to service or repair the laminator.
Unplug the unit and contact an authorised GBC service representative if
one or more of the following has occurred:
• The power supply cord or attachment plug is damaged.
• Liquid has been spilled into the laminator.
• The laminator is malfunctioning after being mishandled.
• The laminator does not operate as described in these instructions.
m
Service
WARNING: THIS IS NOT A TOY - DO NOT ALLOW
CHILDREN TO OPERATE THIS LAMINATOR!
m
Installation
• Shipping damage should be brought to the immediate attention of the
delivering carrier.
• Place the laminator on a stable flat surface capable of supporting
50kg. The surface should be at least 76cm high to assure comfortable
positioning during operation. All four rubber feet should be on the
supporting surface.
• Connect power cord to an appropriate power source. Avoid connecting
other equipment to the same branch circuit to which the laminator is
connected as this may cause nuisance tripping of the circuit breaker
or blown fuses.
• The laminator should be positioned to allow exiting film to drop freely
to the floor. Accumulation of laminate as it exits the laminator may
cause film to wrap around the rollers causing a jammed condition.
• Avoid placing laminator near sources of heat or cold. Avoid locating the
laminator in the direct path of forced, heated or cooled air.
Caring for the AutoUltima Pro Laminator
The only maintenance required by the operator is to periodically dean
the heal shoes. This should only be done when changing film rolls,
please see page 7 steps 1, 2, &3. The following procedure will help keep
the heal shoes free of adhesive that has been deposited along the edge
of the laminating film.
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED
WHILE THE LAMINATOR IS HOT. USE EXTREME CAUTION.
WARNING: Do not apply cleaning fluids or solvents to
the rollers.
WARNING: Do not attempt to laminate adhesives
marked 'flammable'.
1
Preheat the laminator using the heat button.
2
Clean the top and bottom heat shoes with a soft cloth.
3
Follow the procedure on page 7, steps 4, 5, 6 & 7.
NOTE:
Do not use metal scouring pads to clean the heat shoes!
WARNING:
Do not laminate glitter and/or metallic items. Damage to
the rollers may result.
m
m
m
Summary of Contents for AutoUltima Pro
