background image

 GBC AdvancedPunch Pro 

08/20/2015 

Installation Instructions- DFA 

 

8-1 

Section Contents

 

8. Installation Instructions- DFA 

Section Contents 

Title 

Page 

 

8.1.

 

Introduction .................................................................................. 8-3

 

8.1.1

 

Check the Packing List .......................................................... 8-3

 

8.2.

 

Space Requirements - Dimensions ............................................. 8-3

 

8.2.1

 

Check that the SEM Module is in place. ............................... 8-3

 

8.3.

 

Remove the Packing Materials .................................................... 8-4

 

8.3.1

 

Install the Lift Kit Assembly ................................................... 8-6

 

8.3.2

 

Rotate the AdvancedPunch Pro to the upright Position ........ 8-7

 

8.4.

 

Inspect for Damage ...................................................................... 8-9

 

8.5.

 

Check Input Power ....................................................................... 8-9

 

8.6.

 

DFA Conversion ........................................................................... 8-9

 

8.7.

 

Prepare the Docking Brackets ..................................................... 8-9

 

8.7.1

 

Install the Upstream Docking Bracket ................................... 8-9

 

8.7.2

 

Install the Downstream Docking Bracket .............................. 8-9

 

8.8.

 

Level the Punch ......................................................................... 8-10

 

8.9.

 

Dock the AdvancePunch Pro  to the Upstream Device ............. 8-11

 

8.10.

 

Install the CNC-DFA Circuit Board and Cables ......................... 8-11

 

8.11.

 

Connect the Punch Cables ........................................................ 8-12

 

8.12.

 

Install the Lift Kit Cover .............................................................. 8-13

 

8.13.

 

Dock the AdvancedPunch Pro  to a Downstream Device ......... 8-13

 

8.14.

 

Install the Die Set ....................................................................... 8-13

 

8.15.

 

Power up the Punch ................................................................... 8-14

 

8.16.

 

Configure the Punch .................................................................. 8-15

 

8.17.

 

Firmware Installation .................................................................. 8-15

 

8.18.

 

Run the Punch in Bypass Mode................................................. 8-16

 

8.19.

 

Run the Punch in Punch Mode .................................................. 8-17

 

8.19.1

 

Punch Quality ...................................................................... 8-18

 

8.20.

 

Alignments/Adjustments ............................................................ 8-18

 

8.20.1

 

Center the Punch ................................................................ 8-18

 

8.21.

 

Tag Matrix .................................................................................. 8-19

 

8.22.

 

Operator Manual ........................................................................ 8-19

 

8.23.

 

Tools .......................................................................................... 8-19

 

 

 

 

Summary of Contents for AdvancedPunch Pro

















































































































































































































































































































































































































Reviews: