background image

15

EN

14

FACTORY SETTINGS

All settings are saved in the 

Gauss MiL`s

 memory after it’s turned off 

and are automatically restored after it’s turned on.

1.

2.

3.

TO RETURN YOUR SETTINGS TO THEIR 

FACTORY PRESETS, PERFORM THE 

FOLLOWING STEPS:

Turn off the detector.

Press and hold          , turn on the detector 

using          .

Hold  down              and  wait  until  all  options  of  the 

Settings Menu briefly appear on the LCD screen.

15

TROUBLESHOOTING

Ensure the battery is sufficiently charged.

Connect the supplied charger to the detector and wait until charging is 

complete.

1.  Check the coil cable, make sure all the contacts are clean.

2.  Ensure the nut on the coil connector is firmly tightened.

3.  Move away from the source of interference. 

4.  Try switching to another operating frequency. 

5.  Reduce the detector’s sensitivity

Ensure the built-in transmitter is turned off.

Ensure both devices are set to the same channel.

Change the mounting spot of the MDLink module. It should be located 

at a place where electromagnetic waves meet no barriers.

Rotate the twist lock in loosening direction and clean it out to remove 

dirt and sand. 

The detector turns on, but 

turns off by itself

The detector doesn’t turn on

Erratic noises

No sound from the built-in 

speaker

No connection with the 

MDLink module

Unstable connection with  the 

MDLink module

The shaft twist lock seizes

Trouble

Solution

Summary of Contents for MIL MD



















Reviews: