background image

CHAPTER 5: Using the BIOS Setup Utility

www.gateway.com

68

3

Remove the jumper across pins 1-2 of header J3-E, then place the jumper 
across pins 2-3.

4

Follow the instructions in 

“Closing the server case” on page 32

.

5

Insert a bootable USB “disk-on-key” containing a valid BIOS image into a 
USB port. 

6

Reconnect the power cords and turn on the server. The BIOS recovery is 
initiated.

7

While the BIOS is being recovered, the monitor displays a blue screen and 
the server will beep continually. The process is complete when the server 
stops beeping.

8

Remove the bootable USB “disk-on-key.”

9

Turn off the server, then disconnect the power cords and all other cables 
connected to the server.

10

Follow the instructions in 

“Opening the server case” on page 31

.

11

Place the jumper back onto pins 1-2.

12

Follow the instructions in 

“Closing the server case” on page 32

.

13

Plug in the AC power cords and turn on the server, then verify that the 
recovery was successful.

Resetting the BIOS

You can use two methods to clear all BIOS Setup settings and return them to 
the factory defaults:

Press the power and reset buttons on the front of the server.

Move the Clear CMOS jumper on the system board.

Summary of Contents for E-9525R



































































































































Reviews: