background image

2

Caution

 Do not store the unit in a place of much 
moisture or dust or place of high 
temperature.

 Incompliance may lead to trouble.

 Do not use or leave the unit in a place of 
high temperature exposed to direct sunlight 
or in a vehicle under the hot sun.

 Incompliance may lead to deformation or 

trouble of equipment

Do not place the unit on any unstable place 
such as shaky table or tilted place.

 The unit may drop and cause injury and 

trouble.

 In measuring the tension, always make 
sure that the machine is stopped by turning 
off motor power supply or the lik

The arm of flexible arm microphone is a 
universal pipe, but must not be bent at an 
acute angle. In addition, do not bend the 
pipe within 20 mm from the top of 
microphone and at the root of connector. 
Further, do not hold and pull strongly or 
turn the microphone (sensor) and the arm. 
Do not hold and pull strongly or turn the 
microphone (sensor) of cord type 
microphone and electromagnetic sensor.

 When it starts thundering while using this 
unit outdoors, turn off power at once and 
move to a safe place.

 Incompliance may lead to thunderbolt 

and electric shock.

Do not use solvent (such as thinner and 
benzene) in taking care of the main body.

Summary of Contents for U-507

















Reviews: