GASTRON GTD-3000Tx Page 7 Instruction Manual Download

Page: 7 / 18

www.gastron.com

5. Installation

GTD-3000TxW

Instruction Manual

It is prohibited for an individual, other than an approved user or a technician responsible for installation and repair from

the head office, to install a gas leak detector on site or open the cover of the installed gas leak detector and manipulate

it. This may cause serious loss of life and property from fire, explosion, and etc. In addition, please check whether there

is any remaining explosive gas or combustible material in the surroundings. Power must be turned off before performing

work.

[Figure 4. Display Part Detaching Method]

5.2. Main PCB Configuration

■ After detaching the display parts, the Main PCB terminal layout appears as shown in the figure below.

[Table 2. Main PCB 주요 Part 설명]

NAME

DESCRIPTION

CN8

Power & Output Signal Terminal

4~20mA Source / Sink 선택 점퍼(ON: Source Type, OFF: Sink Type)

CN4

Display LCD Connector

CN1

Sensor Connector

CN5

Program download Connector

Status LED (Flashes in 1 sec interval during normal operation)

OC1, OC2, OC3

HART Option Board Connector

CN3

Warning light (GTL-100) Interface Connector

[Figure 5. Main PCB Terminal Layout]

■ Using OC1, OC2, and OC3 shown in the layout above, HART Option RS-485 MODBUS board can be attached.

3ØScrew holes located at top left of option board are used for fixing.

[Figure 3. Slotted Set Screw]

■ After detaching the cover, disassemble the display parts

as below.

① Push in left and right fixing rings located on front

side of LCD at the same time.

② While pushing, pull the display parts towards the

front to detach from gas detector body.

③ After detaching the display parts, the Main PCB

is installed at the bottom part of the detector body.

■ <Warning - Do not open when electical current is

flowing>

■ Turn the slotted set screw (M4 x 1ea) fixing the

cover part of main body 3~4 tuns counter

clockwise (ccw) using a hex wrench (M2) then

turn the cover of gas leak detector ccw to detach

the cover. When the cover is detached,

LCD appears.

5.1. Detachment of Housing Cover

Summary of Contents for GTD-3000Tx



















Search results

Summary of Contents for GTD-3000Tx

Reviews:

Related manuals for GTD-3000Tx

Brands by name

Popular brands

GASTRON GTD-3000Tx, Instruction Manual

Search results

Summary of Contents for GTD-3000Tx

Reviews:

Related manuals for GTD-3000Tx

Brands by name

Popular brands