www.gastron.com
26
_
27
7. System Mode
7. System Mode
GTD-3000TxW
Instruction Manual
7.3. ALARM MODE
PASSWORD
[**]
- Contacting "FUNC" key with the Magnet-bar for 2 s or longer in Measuring Mode enters Password
-
mode.
- After setting Password using "↑" or "↓" key, contact "FUNC" key.
ALARM PROGRAM
MODE
- Contact "↑" or "↓" key to select "Alarm Program Mode".
- Contact "FUNC" key when "ALARM PROGRAM MODE" is displayed to enter Alarm setting mode.
- Contact "RESET" key to return to Measuring Mode.
ALARM OPERATING
[ AUTO ]
- It is a mode that sets reset method after an event of alarm. Contacting "↑" or "↓" key changes between
-
"AUTO" and "MANUAL".
- "AUTO" mode automatically resets the alarm. "MANUAL" mode resets the alarm only when Reset key is
-
pressed.
ALARM OPERATING
[ MANUAL]
ALARM RELAY TYPE
DE-ENERGIZED
- It is a mode that sets Reset method after an event of Alarm. Contacting "↑" or "↓" key changes between
-
"DE-ENERGIZED" and "ENERGIZED".
- "DE-ENERGIZED" deactivates energizer mode and "ENERGIZED" activates energizer mode.
FAULT RELAY TYPE
DE-ENERGIZED
- It is a mode that sets Reset method after an event of FAULT. Contacting "↑" or "↓" key changes
-
between "DE-ENERGIZED" and "ENERGIZED".
- "DE-ENERGIZED" deactivates energizer mode and "ENERGIZED" activates energizer mode.
ALARM1 TYPE SEL.
[INCREASE ]
- It is a mode that sets operational direction of Alarm1. Contact "↑" or "↓" key to display "INCREASE" or
-
"DECREASE".
- "INCREASE" mode runs when the value is at Alarm1 threshold or higher. "DECREASE" mode runs when
-
the value is at Alarm 1 threshold or lower.
ALARM1 TYPE SEL.
[DECREASE ]
ALARM1 LEVEL ADJ
[ 20]
- It is a mode that sets Alarm1 level threshold. Contact "↑" or "↓" key to increase or decrease Alarm1 level,
-
respectively.
- When a desired alarm 1 threshold is displayed, contact "FUNC" key to set it and enter the next item.
ALARM1 DEAD BAND
[ 0.0]%FS
- It is a mode that sets operation range of Alarm1. Contact "↑" or "↓" key to increase or decrease the value,
-
respectively.
- When Alarm1 is in "INCREASE" mode, it runs at Alarm1 thr Dead band and is released at
-
Alarm1 threshold - Dead band.
- When a desired value is displayed, contact "FUNC" key to set the dead band value and enter the next
-
Alarm Program Mode
ALARM1 TIME SET
[ 1] SEC
- It is a mode that sets Alarm1 dwell time. Contact "↑" or "↓" key to increase or decrease the value,
-
respectively.
- Displayed number is in sec and in a range from 0 to 60. When a desired value is displayed, contact
-
"FUNC" key to set the alarm dwell time and enter the next Alarm Program mode.
ALARM1 RELAY CTL
[ ON]
- It is a mode that sets whether to contact relay contact during Alarm1 operation. Contact "↑" or "↓" key to
-
change the display between "ON" or "OFF".
- In ON mode, relay runs during Alarm1 operation. In OFF mode, relay do not run during Alarm1 operation.
ALARM2 TYPE SEL.
[INCREASE ]
- It is a mode that sets operational direction of Alarm2. Contact "↑" or "↓" key to display "INCREASE" or
-
"DECREASE".
- "INCREASE" mode operates when the value is equal or larger than set alarm threshold. "DECREASE"
-
mode operates when the value is equal or less than set alarm threshold.
ALARM2 TYPE SEL.
[DECREASE ]
ALARM2 LEVEL ADJ
[ 40 ]
- It is a mode that sets Alarm2 level. Contact "↑" or "↓" key to increase or decrease Alarm2 level,
-
respectively.
- When a desired alarm 2 threshold is displayed, press "FUNC" KEY to set it and enter the next Alarm
-
Program mode.
ALARM2 DEAD BAND
[ 0.0 ]%FS
- It is a mode that sets operational direction of Alarm2. Contact "↑" or "↓" key to increase or decrease
-
the value, respectively.
- When Alarm2 is in "INCREASE" mode, it runs at Alarm1 thr Dead band and is released at
-
Alarm2 threshold - Dead band.
- When a desired value is displayed, contact "FUNC" key to set the dead band value and enter the next
-
Alarm Program Mode
ALARM2 TIME SET
[ 1] SEC
- It is a mode that sets Alarm2 dwell time. Contact "↑" or "↓" key to increase or decrease the value,
-
respectively.
- Displayed number is in sec and in a range from 0 to 60. When a desired value is displayed, contact
-
"FUNC" key to set the alarm dwell time and enter the next Alarm Program mode.
ALARM2 RELAY CTL
[ ON]
- It is a mode that sets whether to contact relay contact during Alarm2 operation. Contact "↑" or "↓" key
-
to change the display between "ON" or "OFF".
- In ON mode, relay runs during Alarm2 operation. In OFF mode, relay do not run during Alarm2
-
operation.
