GASTRON GTC-700 Instruction Manual Download Page 2

Gas & Flame 

Detection System

GTC-700

Instruction Manual

www.gastron.com

02

_

03

Thank you very much for purchasing a product from Gastron Co. Ltd.

Our Gastron Co.Ltd. is a company specialized in Gas Detector & Gas Monitoring System and have been 

recognized by many customers for the best quality and use convenience. We always seek to help our 

customers to find the product they need and we continuously research to develop gas detectors that satisfies 

our customers. From now on, you can solve all problems related to gas detectors with the products of 

Gastron. We Gastron will be responsible for your satisfaction.

This user manual describes operation and simple maintenance methods etc. for the gas detector. Please read 

carefully and store it in a safe place. Using it as a reference will help a lot when you have a question during 

use.

* KOSHA GUIDE : P-135/6-2018

  Calibration must be performed at a frequency requested by the manufacturer and shall be performed quarterly when    

  the calibration period is not specified.

The product and manual are subject to change without a notice for the product's functional improvement and ease of use.

■ For accurate operation of the gas detector, please perform an inspection and a calibration at 

  least once per 6 months.

  ( * In reference to KOSHA GUIDE: P-135/6-2018 / 7.2 In-house inspection, section 2)

■ For accurate operation of the gas detector, inspection and calibration using a reference gas before 

  measurement is recommended.

■ Failure to calibrate may result in malfunction of the equipment due to aging of the sensor.
■ Only an individual specialized in gas detector may disassemble the device.
■ Wire specification for the power cable must be decided in reference to the "Installation cable length" 

 section.

■ Please contact our company's technical support, e-mail, or website for inquiries related to 

  inspection and calibration of the gas detector.

Greetings

In case of a problem after purchasing the product,

please contact the address below.

· Address  : 23 Gunpo Advanced Industry 1-ro,

 

  Gunpo-si, Gyeonggi-do

· Tel  

: 031-490-0800

· Fax  

: 031-490-0801

· URL 

: www.gastron.com

· e-mail 

: [email protected]

Summary of Contents for GTC-700



















Reviews: