Gastroback DESIGN JUICER BASIC Operating Instructions Manual Download

Page: 9 / 62

(earth/ground) connected properly. Ensure that the ratings of your mains

power supply correspond to the requirements of the appliance (220/240

V AC, 50/60 Hz, rated for 16 A). The installation of a residual current

operated circuit breaker (r.c.c.b.) with a maximum rated residual opera-

ting current of 30 mA in the supplying electrical circuit is strongly recom-

mended. If in doubt, contact your electrician for further information.
• In various foreign countries, the specifications for power supplies are

subject to incompatible norms. Therefore, it is possible that power sup-

plies in foreign countries do not meet the requirements for safe opera-

tion of the appliance. Thus, before operating the appliance abroad,

ensure that safe operation is possible.

• Do not use any desk top multi socket outlet, external timer, remote

control system or extension cord. The power outlet must always be

easily accessible for unplugging the appliance immediately in case

of any malfunction or danger.Always handle power cords with care.

The pins of the power plug must be smooth, dry, and clean without

discolourations. Always unwind the power cord completely for opera-

tion to avoid hazard of overheating, fire, and electric shock.

Do not

attempt to operate the appliance with the power cord damaged

in any way to avoid risk of overheating, fire, and electric shock.

• Do not place the appliance on a power cord. Power cords may never

be knotted, twisted, pulled, strained or squeezed. Do not let the plug

or power cord hang over the edge of the table or counter. The power

cord may never touch hot surfaces, sharp edges, or any moving parts.

Ensure that no one will pull the appliance by the power cord or will

entangle in the power cord. Always grasp the plug to disconnect

the power cord. Do not touch the appliance or power plug with wet

hands, while the appliance is connected to the power supply.

• Keep the motor base and power cord always completely dry. If

liquids run out or are spilled onto the exterior of the appliance, imme-

diately unplug the appliance. Always wipe off spilled liquids immedi-

ately. If in doubt, check the used processing system (juicing system or

optional accessory) for leakage and overflow, before operating the

appliance again.

Summary of Contents for DESIGN JUICER BASIC































































Search results

Summary of Contents for DESIGN JUICER BASIC

Reviews:

Related manuals for DESIGN JUICER BASIC

Brands by name

Popular brands

Gastroback DESIGN JUICER BASIC, Operating Instructions Manual

Search results

Summary of Contents for DESIGN JUICER BASIC

Reviews:

Related manuals for DESIGN JUICER BASIC

Brands by name

Popular brands