background image

the appliance close to the edge of the working area. Ensure that the power supply
cable does not hang down from the work surface as it could be easily pulled, particularly
by small children, thereby causing serious accidents. 

Never

immerse the motor block in water! Short-circuit danger! Do 

not

put any

cloth or napkins underneath the appliance to avoid endangering by fire and electric
shocks. 

Never 

cover the air box underneath the appliance. 

Never

place the appliance on

paper towels or uneven working areas. The air has to able to circulate.

Never

situate the appliance close to a strong heat source or a hot surface (for

example: heater, stove or grill).

• Ensure that the switch and cable do not come into contact with water!
Should this  inadvertently happen, all parts must be completely dry before the appliance is
used again.

Never

let water or other liquids run into the motorblock. Do 

not 

use the appliance

in moist and wet areas. 

Never 

clean the line cord or the appliance in the dishwasher, pour liquids

over the appliance or douse or dip it in water or other liquids. In case that water or other
liquids ran into the appliance while operating turn off the appliance immediately, pull the
plug and dry the appliance with a clean cloth (´Care and cleaning`). 

Never leave the appliance unattended when the plug is connected

to the power outlet. 

Always disconnect the power supply cable from the mains

before assembling, dismantling and cleaning the appliance or before exchanging
the grinding discs. Always uncoil the line cord completely before installing the appliance.
When pulling the plug always catch hold of the enclosure of the plug. Always grab
hold on both sides underneath the appliance when moving it.

• Do not let the motor run longer then necessary to prevent overheating. After turning
off the appliance the motor needs about 6 sec. to stop moving. Wait for the motor
to stop completely and press the power button before disassembling the appliance
or continuing operation.

• Clean the appliance straight after use and rinse off leftover food. Remove such
dirt immediately and operate according to the instructions ´Care and cleaning`
before storing the appliance. Do not let food desiccate on the appliance.

• To avoid damage, 

do not

use any abrasive cleaners, corrosive chemicals

(i.e. disinfectants, bleach) or cleaning pads for operation or cleaning. 

Never 

clean

or operate the appliance or units of the appliance with abrasive or hard sharp-edged
items. 

Never put the appliance or parts of the appliance in the dishwasher

for cleaning! This will cause discolouration and corrosion.

27

41406_designfleischwolfelectronicpro_manual_GermanEnglisch_neu.qxp  20.10.2009  11:00  Seite 

Summary of Contents for 41406






















Reviews: