gassero wallcon 115, Installation, User & Service Manual

Page: 28 / 40

REV
.03-(16.03.2015)
Reset funct on
The reset funct on for meters and the resettable parameters
appears on the bottom l ne of the d splay, prov ded a reset s
perm tted on the current operat ng l ne (enduser/comm ss on ng
/ heat ng eng neer).
0 4 8 12 16 20 24
Reset ? yes
After act vat on of the OK button, d splay shows a flash ng “Yes“
0 4 8 12 16 20 24
Reset ?
yes
After confirmat on w th the OK button, the relevant parameter
When manual control s act ve, the relays are no longer energ zed
and deenerg zed accord ng to the control state, but are set to a
predefined manual operat ng state depend ng on the r funct on.
The burner relay energ zed n manual control can be deenerg zed
by the electron c temperature controller (TR).
After manual control has been act vated, a change to the bas c
d splay must be made. There, the ma ntenance / spec al mode
symbol Press the Info button to sw tch to nfo
d splay “Manual mode“, where the setpo nt can be adjusted.
The ch mney sweep funct on s act vated by a short press
(max mum 3 seconds) on the ch mney sweep button. It
produces the operat ng state requ red for mak ng flue gas
or parameters w ll be reset.
Manual Control
appears.
Ch mney sweep funct on
measurements.
SLT test
The SLT test (SLT = safety l m t thermostat) s act vated
by a long press (longer than 3 seconds) on the ch mney
sweep button. The button must be kept depressed dur ng
the ent re test.If released, the test w ll be aborted. The
SLT test s shown on the d splay.
The test must be made by qual fied techn c ans s nce
the bo ler temperature w ll be ra sed above the max mum
l m tat ons.
5.2 PROGRAMMING
Sett ng pr nc ple
Sett ngs that cannot be made d rectly w th the help of
operat ng elements are made through programm ng.
For th s purpose, the nd v dual sett ngs are structured
n the form of operat ng pages and operat ng l nes,
thus form ng pract cal groups of sett ngs. The follow ng
Example “Sett ng the t me of day“
When press ng the ESC button, you go back one step;
adjusted values w ll not be adopted
If any sett ng s made for 8 m nutes, the un t w ll
automat cally return to the bas c d splay
Operat ng l nes may be h dden, depend ng on the
type of un t, the configurat on and
user level
operat on D splay example Descr pt on
1
0 4 8 12 16 20 24
AUTO
Room temperature
You w ll see the bas c d splay.
If the bas c d splay s not shown, press
the ESC button to return to t.
Press the OK button.
2
Text3
0 4 8 12 16 20 24
AUTO
Operator sect on
T me of day and date
The bottom sect on of the d splay
shows a number of operat ng pages.
Turn the sett ng knob unt l operat ng
page “T me of day and date“ appears.
To confirm, press the OK button.
3
0
4 8 12 16 20 24
AUTO
T me of day and date
Hours / m nutes
In the bottom sect on of the d splay, the
first operat ng l ne of operat ng page
“T me of day and date“ appears.
Turn the sett ng knob unt l operat ng
l ne “Hours / m nutes“ appears.
To confirm, press the OK button.
4
0 4 8 12 16 20 24
AUTO
T me of day and date
Hours / m nutes
The d splay shows the hours flash ng.
Turn the sett ng knob unt l the hours of
the t me of day are correct.
To confirm, press the OK button.
example wh ch shows the sett ng of the t me of day and
date shall expla n th s.
5
0 4 8 12 16 20 24
AUTO
T me of day and date
Hours / m nutes
The d splay shows the m nutes
flash ng.
Turn the sett ng knob unt l the m nutes
of the t me of day are correct.
To confirm, press the OK button.
6
T me of day and date
0 4 8 12 16 20 24
AUTO
Hours / M nutes
The sett ngs are saved, the d splay
stops flash ng.
You can cont nue to make other
sett ngs, or
you press the operat ng mode button to
return to the bas c d splay.
7 Now, you have returned to the bas c
d splay.
T me of day and date
Operator sect on
W reless
T me program heat ng c rcu t 1
T me program heat ng c rcu t 2
T me program heat ng c rcu t P
Hol days heat ng c rcu t 1
D agnost cs of consumers
Hours / m nutes
Month / day
Year
Start of summer t me
End of summer t me
Hours 1...24 h
M nutes 0...60 m n
Example of menu structure
Operat on
27