7
6
ASSEMBLY INSTRUCTIONS
Your fire table must be installed on flat, stable
surface, away from any combustible materials or
construction.
Make sure the appliance control knob is turned
“off” before assembling.
Note: Remove any transit protection material.
Tools required:
• Philips head screwdriver (or cordless drill
and bits).
• Flat head screwdriver.
• Adjustable spanner.
STEP 1
Inside of the LPG compartment the gas hose and
regulator assembly are already connected to the
gas inlet of the appliance.
Place LPG cylinder in the LPG compartment.
Make sure the LPG cylinder base sits inside the
metal stand easily and completely.
Turn the wing screw on the outer part of the metal
stand clockwise to secure the LPG cylinder tightly.
STEP 2
Ensure cylinder valve is in its full off position.
Check for any damage to either the cylinder
connection or the hose. NEVER attempt to use
damaged equipment. Attach the regulator and
hose to your gas cylinder. Tighten the nut to a
positive stop by hand.
STEP 3
Turn on the gas cylinder ensuring that the control
knob on the outdoor heater is turned OFF at this
point. DO NOT ATTEMPT TO LIGHT THE HEATER.
STEP 4
Use a solution of soapy water (dishwashing liquid
and water is fine). Brush it on or use a spray bottle
as shown in the drawing. Ensure the connections
have a good coating.
STEP 5a
If the connection is leaking, bubbles will start to
grow in the soapy solution. If this happens shut off
the gas supply at the cylinder.
STEP 11
Ensure cylinder valve is in its full off position. Check
for any damage to either the cylinder connection or
the hose. NEVER attempt to use damaged equipment.
Attach the regulator and hose to your gas cylinder.
Tighten the nut to a positive stop by hand.
STEP 12
Turn on the gas cylinder ensuring that the control knob
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.
STEP 13
Use a solution of soapy water (dishwashing liquid and
water is fine). Brush it on or use a spray bottle as
shown in the drawing. Ensure the connections have a
good coating.
STEP 14a
If the connection is leaking, bubbles will start to grow
in the soapy solution. If this happens shut off the gas
supply at the cylinder.
STEP 14b
Tighten the connections using a crescent then repeat
steps 12-13.
STEP 14c
The connection is gas tight when no bubbles grow
around the gas connection.
ASSEMBLY INSTRUCTIONS
STEP 11
Ensure cylinder valve is in its full off position. Check
for any damage to either the cylinder connection or
the hose. NEVER attempt to use damaged equipment.
Attach the regulator and hose to your gas cylinder.
Tighten the nut to a positive stop by hand.
STEP 12
Turn on the gas cylinder ensuring that the control knob
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.
STEP 13
Use a solution of soapy water (dishwashing liquid and
water is fine). Brush it on or use a spray bottle as
shown in the drawing. Ensure the connections have a
good coating.
STEP 14a
If the connection is leaking, bubbles will start to grow
in the soapy solution. If this happens shut off the gas
supply at the cylinder.
STEP 14b
Tighten the connections using a crescent then repeat
steps 12-13.
STEP 14c
The connection is gas tight when no bubbles grow
around the gas connection.
ASSEMBLY INSTRUCTIONS
STEP 11
Ensure cylinder valve is in its full off position. Check
for any damage to either the cylinder connection or
the hose. NEVER attempt to use damaged equipment.
Attach the regulator and hose to your gas cylinder.
Tighten the nut to a positive stop by hand.
STEP 12
Turn on the gas cylinder ensuring that the control knob
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.
STEP 13
Use a solution of soapy water (dishwashing liquid and
water is fine). Brush it on or use a spray bottle as
shown in the drawing. Ensure the connections have a
good coating.
STEP 14a
If the connection is leaking, bubbles will start to grow
in the soapy solution. If this happens shut off the gas
supply at the cylinder.
STEP 14b
Tighten the connections using a crescent then repeat
steps 12-13.
STEP 14c
The connection is gas tight when no bubbles grow
around the gas connection.
ASSEMBLY INSTRUCTIONS
STEP 11
Ensure cylinder valve is in its full off position. Check
for any damage to either the cylinder connection or
the hose. NEVER attempt to use damaged equipment.
Attach the regulator and hose to your gas cylinder.
Tighten the nut to a positive stop by hand.
STEP 12
Turn on the gas cylinder ensuring that the control knob
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.
STEP 13
Use a solution of soapy water (dishwashing liquid and
water is fine). Brush it on or use a spray bottle as
shown in the drawing. Ensure the connections have a
good coating.
STEP 14a
If the connection is leaking, bubbles will start to grow
in the soapy solution. If this happens shut off the gas
supply at the cylinder.
STEP 14b
Tighten the connections using a crescent then repeat
steps 12-13.
STEP 14c
The connection is gas tight when no bubbles grow
around the gas connection.
ASSEMBLY INSTRUCTIONS
Summary of Contents for Keystone GM142-140
Page 10: ...10 This page has been intentionally left blank ...
Page 11: ...11 This page has been intentionally left blank ...
Page 12: ...12 ...
